Corrigendum to Commission Implementing Regulation (EU) 2016/799 of 18 March 2016 implementing Regulation (EU) No 165/2014 of the European Parliament and of the Council laying down the requirements for the construction, testing, installation, operation and repair of tachographs and their components (Official Journal of the European Union L 139 of 26 May 2016)
Grade B
mapped from publisher markup. A grade says how a document's structure was obtained, not how reliable the law is.
Address https://gelex.eu/eli/EU/corrigendum/oj/L/2016/146/07@2016-06-03/en
Annex II is inserted as follows:
ANNEX
ANNEX II APPROVAL MARK AND CERTIFICATE
I.1.2.3. APPROVAL MARK The approval mark shall be made up of: The approval mark shall be shown on the descriptive plaque of each set of equipment and on each record sheet and on each tachograph card. It must be indelible and must always remain clearly legible. The dimensions of the approval mark drawn below are expressed in millimetres, these dimensions being minima. The ratios between the dimensions must be maintained.
I.1.
(a) a rectangle, within which shall be placed the letter e followed by a distinguishing number or letter for the country which has issued the approval in accordance with the following conventional signs: Belgium 6, Bulgaria 34, Czech Republic 8, Denmark 18, Germany 1, Estonia 29, Ireland 24, Greece 23, Spain 9, France 2, Croatia 25, Italy 3, Cyprus CY, Latvia 32, Lithuania 36, Luxembourg 13, Hungary 7, Malta MT, Netherlands 4, Austria 12, Poland 20, Portugal 21, Romania 19, Slovenia 26, Slovakia 27, Finland 17, Sweden 5, United Kingdom 11, and
(b) an approval number corresponding to the number of the approval certificate drawn up for the prototype of the recording equipment or the record sheet or to the number of a tachograph card, placed at any point within the immediate proximity of that rectangle.
II.
APPROVAL CERTIFICATE FOR ANALOGUE TACHOGRAPHS A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.
APPROVAL CERTIFICATE
Name of competent administration … Notification concerning: Approval No: …. (Signature)
approval of a type of recording equipment
withdrawal of approval of a type of recording equipment
approval of a model record sheet
withdrawal of approval of a model record sheet
1. Trade mark or name …
2. Name of type or model …
3. Name of manufacturer …
4. Address of manufacturer …
5. Submitted for approval on …
6. Tested at …
7. Date and number of the test(s) …
8. Date of approval …
9. Date of withdrawal of approval …
10. Type or types of recording equipment in which sheet is designed to be used
11. Place …
12. Date …
13. Descriptive documents annexed …
14. Remarks (including the position of seals if applicable)
III.
APPROVAL CERTIFICATE FOR DIGITAL TACHOGRAPHS A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.
APPROVAL CERTIFICATE FOR DIGITAL TACHOGRAPHS ☐☐
Name of competent administration … Notification concerning: approval of: withdrawal of approval of: Approval No: …. (Signature)
☐
recording equipment model
recording equipment component
a driver's card
a workshop card
a company card
a controller's card
1. Manufacturing brand or trademark …
2. Name of model …
3. Name of manufacturer …
4. Address of manufacturer …
5. Submitted for approval for …
6. Laboratory(-ies) …
7. Date and number of test report …
8. Date of approval …
9. Date of withdrawal of approval …
10. Model of recording equipment(s) with which the component is designed to be used
11. Place …
12. Date …
13. Descriptive documents annexed …
14. Remarks (including the position of seals if applicable)
IV.
APPROVAL CERTIFICATE FOR SMART TACHOGRAPHS A Member State which has granted approval shall issue the applicant with an approval certificate, the model of which is given below. When informing other Member States of approvals issued or, if the occasion should arise, withdrawn, a Member State shall use copies of that certificate.
APPROVAL CERTIFICATE FOR SMART TACHOGRAPHS ☐☐
Name of competent administration … Notification concerning: approval of: withdrawal of approval of: Approval No: …. (Signature)
☐
recording equipment model
recording equipment component
a driver's card
a workshop card
a company card
a controller's card
1. Manufacturing brand or trademark …
2. Name of model …
3. Name of manufacturer …
4. Address of manufacturer …
5. Submitted for approval for …
6.
(a) Test laboratory for functional certification …
(b) Test laboratory for security certification …
(c) Test laboratory for interoperability certification …
7.
(a) Date and number of functional certificate …
(b) Date and number of security certificate …
(c) Date and number of interoperability certificate …
8. Date of approval …
9. Date of withdrawal of approval …
10. Model of recording equipment(s) with which the component is designed to be used
11. Place …
12. Date …
13. Descriptive documents annexed …
14. Remarks (including the position of seals if applicable)