Address https://gelex.eu/eli/EU/regulation/2018/2069@2018-12-20/en

Contents

1. Preamble
2. 1. Article 1
   2. Article 2
3. ANNEX

THE COUNCIL OF THE EUROPEAN UNION,

Having regard to the Treaty on the Functioning of the European Union, and in particular Article 31 thereof,

Having regard to the proposal from the European Commission,

Whereas:

(1) In order to ensure a sufficient and uninterrupted supply of certain agricultural and industrial products which are unavailable in the Union and thereby avoid any disturbances in the market for those products, autonomous Common Customs Tariff (CCT) duties on those products have been suspended by Council Regulation (EU) No 1387/2013. Those products can be imported into the Union at reduced or zero duty rates.

(2) The Union production of 87 products that are not listed in the Annex to Regulation (EU) No 1387/2013 is inadequate or non-existent. It is therefore in the interest of the Union to suspend totally the autonomous CCT duties on those products.

(3) It is necessary to modify the conditions for the suspension of autonomous CCT duties for 26 products listed in the Annex to Regulation (EU) No 1387/2013 in order to take into account technical product developments and economic trends in the market.

(4) For certain products listed in the Annex to Regulation (EU) No 1387/2013, the classification in the Combined Nomenclature (CN) of the products covered by suspensions should be amended.

(5) It is also necessary, in the interest of the Union, to amend the end date for the mandatory review of 720 products listed in the Annex to Regulation (EU) No 1387/2013 in order to allow duty-free imports beyond that date. The autonomous CCT duty suspensions for those products have been reviewed and new revised dates should be set for their next mandatory review.

(6) It is no longer in the interest of the Union to maintain the suspension of autonomous CCT duties for 13 products listed in the Annex to Regulation (EU) No 1387/2013. The suspensions for those products should therefore be deleted. Moreover, according to the communication from the Commission concerning autonomous tariff suspensions and quotas (the Commission communication), for practical reasons, requests for tariff suspensions or quotas where the amount of uncollected customs duty is estimated to be less than EUR 15000 per year cannot be taken into consideration. The mandatory review of the existing suspensions has indicated that imports in relation to 197 products listed in the Annex to Regulation (EU) No 1387/2013 do not reach that threshold. Those suspensions should therefore be deleted.

(7) In the interest of clarity, and taking into account the number of amendments to be made, the Annex to Regulation (EU) No 1387/2013 should be replaced.

(8) Regulation (EU) No 1387/2013 should therefore be amended accordingly.

(9) In order to avoid any interruption of the application of the autonomous suspension scheme and to comply with the guidelines set out in the Commission communication, the changes provided for in this Regulation regarding the suspensions for the products concerned should apply from 1 January 2019. This Regulation should therefore enter into force as a matter of urgency,

HAS ADOPTED THIS REGULATION:

Article 1

The Annex to Regulation (EU) No 1387/2013 is replaced by the text set out in the Annex to this Regulation.

Article 2

This Regulation shall enter into force on the day following that of its publication in the Official Journal of the European Union. It shall apply from 1 January 2019.

This Regulation shall be binding in its entirety and directly applicable in all Member States. Done at Brussels, 20 December 2018. For the Council The President E. Köstinger

ANNEX

industrial monocarboxylic fatty acids of subheading 38231910,

methyl esters of fatty acids of heading 2915 or 2916,

fatty alcohols of subheadings 290517, 290519 and 382370 used for the manufacture of cosmetics, washing products or pharmaceutical products,

fatty alcohols of subheading 290516, pure or mixed, used for the manufacture of cosmetics, washing products or pharmaceutical products,

stearic acid of subheading 38231100,

goods of heading 3401, or

fatty acids with high purity of heading 2915

conjugated linoleic acid of heading 3823, or

ethyl- or methyl esters of linoleic acid of heading 2916

15 % or more but not more than 35 % of wheat derived Maltodextrin,

15 % or more but not more than 35 % of whey (milk serum),

10 % or more but not more than 30 % of refined, bleached, deodorised and non-hydrogenated sunflower oil,

10 % or more but not more than 30 % of blended, aged spray dried cheese,

5 % or more but not more than 15 % of buttermilk, and

0,1 % or more but not more than 10 % of sodium caseinate, disodium phosphate, lactic acid

of the Genus Mangifera spp.,

with a sugar content by weight of not more than 30 %,

of the Genus Carica spp.,

with a sugar content by weight of more than 13 % but not more than 30 %,

of the Genus Psidium spp.,

with a sugar content by weight of more than 13 % but not more than 30 %,

not from concentrate,

of the genus Mangifera,

of a Brix value of 14 or more, but not more than 20,

more than 6 % of salt concentration,

0,1 % or more but not more than 1,4 % of acidity expressed as citric acid monohydrate, and

whether or not but not more than 2000 mg/kg of sodium benzoate according CODEX STAN 192-1995,

not from concentrate,

of the genus Ananas,

of a Brix value of 11 or more but not more than 16,

with a Brix value of more than 20 but not more than 67,

a value of more than EUR 30 per 100 kg net weight,

containing added sugar,

of a Brix value of 40 or more but not more than 66,

in immediate packings of a content of 50 litres or more

with a Brix value of 13,7 or more but not more than 55,

of a value of more than EUR 30 per 100 kg net weight,

in immediate packings of a content of 50 litres or more, and

with added sugar,

with a Brix value of more than 48 but not more than 67,

in immediate packings of a content of 50 litres or more

of the species Euterpe oleracea,

frozen,

not sweetened,

not in powder form,

of a Brix value of 23 or more but not more than 32,

with a Brix value of 10 or more but not more than 13,7,

of a value of more than EUR 30 per 100 kg net weight,

in immediate packings of a content of 50 litres or more, and

without added sugar,

unfermented,

not containing added spirit or sugar, and

in immediate packing of a content of 20 litres or more

more than 30 % but not more than 35 % licorice extract,

more than 65 % but not more than 70 % tricaprylin,

by weight 20 % or more but not more than 70 % free amino acids, and

peptones of which by weight more than 90 % having a molecular weight of not more than 2000 Da

15 % or more but not more than 35 % of buttermilk,

20 % (± 10 %) of lactose,

20 % (± 10 %) of whey protein concentrate,

15 % (± 10 %) of cheddar cheese,

3 % (± 2 %) of salt,

0,1 % or more but not more than 10 % of lactic acid E270,

0,1 % or more but not more than 10 % of gum arabic E414,

90 % or more by weight of saturates, and

not more than 0,03 % by weight of sulphur,

not more than 1 mg/kg of sulphur,

more than 99 % by weight of saturated hydrocarbons,

more than 75 % by weight of n- and iso-paraffinic hydrocarbons with a carbon chain length of 18 or more but not more than 50, and

a kinematic viscosity at 40 °C of more than 6,5 mm2/s, or

a kinematic viscosity at 40 °C of more than 11 mm2/s with a viscosity index of 120 or more

in the form of powder

of a purity by weight of 99,0 % or more

with a median grain size of 0,7 μm or more, but not more than 2,1 μm

where 70 % of the particles have a diameter of not more than 3 μm

with a particle size of not more than 20 μm, and

of a kind used in the production of polyethylene

94 % or more, but less than 98,5 % of aluminium oxide,

2 % (± 1,5 %) of magnesium oxide,

1 % (± 0,6 %) of yttrium oxide,

either 2 % (± 1,2 %) of lanthanum oxide, or

2 % (± 1,2 %) of lanthanum oxide and neodymium oxide,

in the form of powder

with a purity by weight of 99,5 % or more

with a decomposition point of 263 °C or more

with a particle size of 4 μm (± 1 μm)

with a Total-Na2O-content by weight of not more than 0,06 %

of a purity by weight of 99,9 % or more,

with an average grain-size of 0,7 μm or more but not more than 2,1 μm

2 mg/kg or more of arsenic,

200 mg/kg or more of calcium,

200 mg/kg or more of chlorides,

20 mg/kg or more of iron,

150 mg/kg or more of magnesium,

20 mg/kg or more of heavy metals,

300 mg/kg or more of potassium,

300 mg/kg or more of sodium,

200 mg/kg or more of sulphates,

not more than 600 ppm by weight of R134 (1,1,2,2-tetrafluoroethane),

not more than 5 ppm by weight of R143a (1,1,1-trifluoroethane),

not more than 2 ppm by weight of R125 (pentafluoroethane),

not more than 100 ppm by weight of R124 (1-chloro-1,2,2,2-tetrafluoroethane),

not more than 30 ppm by weight of R114 (1,2-dichlorotetrafluoroethane),

not more than 50 ppm by weight of R114a (1,1-Dichlorotetrafluoroethane),

not more than 250 ppm by weight of R133a (1-Chloro-2,2,2-Trifluoroethane),

not more than 2 ppm by weight of R22 (Chlorodifluoromethane),

not more than 2 ppm by weight of R115 (Chloropentafluoroethane),

not more than 2 ppm by weight of R12 (Dichlorodifluoromethane),

not more than 20 ppm by weight of R40 (Methyl chloride),

not more than 20 ppm by weight of R245cb (1,1,1,2,2-pentafluoropropane),

not more than 20 ppm by weight of R12B1 (Chlorodifluorobromomethane),

not more than 20 ppm by weight of R32 (Difluoromethane),

not more than 15 ppm by weight of R31 (Chlorofluoromethane),

not more than 10 ppm by weight of R152a (1,1-Difluoroethane),

not more than 20 ppm by weight of 1131 (1-Chloro-2 Fluoroethylene),

not more than 20 ppm by weight of 1122 (1-Chloro-2,2-Difluoroethylene),

not more than 3 ppm by weight of 1234yf (2,3,3,3-Tetrafluoropropene),

not more than 3 ppm by weight of 1243zf (3,3,3 Trifluoropropene),

not more than 3 ppm by weight of 1122a (1-chloro-1,2-difluoroethylene),

not more than 4,5 ppm by weight of 1234yf+1122a+1243zf (2,3,3,3-tetrafluoropropene, +1-Chloro-1,2-Difluoroethylene+3,3,3-Trifluoropropene),

not more than 3 ppm by weight of any individual unspecified/unknown chemical,

not more than 10 ppm by weight of all unspecified/unknown chemicals combined,

not more than 10 ppm by weight of Water,

with an acidity level of not more than 0,1 ppm by weight,

without Halides,

not more than 0,01 % by volume of High Boilers,

without any odour (no malodour),

0,001 mg/kg or less of tetrachlorodibenzodioxines,

0,001 mg/kg or less of tetrachlorodibenzofurans,

0,2 mg/kg or less of tetrachlorobiphenyls

85 (± 10) % by weight of 4-isobutyl-2-methylbenzaldehyde (CAS RN 73206-60-7)

15 (± 10) % by weight of 2-isobutyl-4-methyllbenzaldehyde (CAS RN 68102-28-3)

40 % (± 2 %) by weight of tetrapropylammonium hydroxide,

0,3 % by weight or less of carbonate,

0,1 % by weight or less of tripropylamine,

500 mg/kg or less of bromide, and

25 mg/kg or less of potassium and sodium taken together

35 % (± 0,5 %) by weight of tetraethylammonium hydroxide,

not more than 1000 mg/kg of chloride,

not more than 2 mg/kg of iron, and

not more than 10 mg/kg of potassium

C.I. Disperse Orange 61 or Disperse Orange 288,

C.I. Disperse Blue 291:1,

C.I. Disperse Violet 93:1,

whether or not containing C.I. Disperse Red 54

Colourant Reactive Yellow 201 (CAS RN 27624-67-5),

1-Naphthalenesulphonicacid,4-amino-3-[[4-[[2-(sulphooxy)ethyl]sulphonyl]phenyl]azo]-, disodium salt (CAS RN 250688-43-8), or

3,5-diamino-4-[[4-[[2-(sulphooxy)ethyl]sulphonyl]fenyl]azo]-2-[[2-sulfo-4-[[2-(sulphooxy)ethyl]sulfonyl]phenyl]azobenzoic acid sodium salt (CAS RN 906532-68-1)

with a colourant C.I. Reactive Red 141 content of 13 % or more by weight, and

containing a preservative

35 % or more but not more than 40 % of 1-[[4-(phenylazo)phenyl]azo]naphthalen-2-ol methyl derivatives (CAS RN 70879-65-1)

not more than 3 % of 1-(phenylazo)naphthalen-2-ol (CAS RN 842-07-9)

not more than 3 % of 1-[(2-methylphenyl)azo]naphthalen-2-ol (CAS RN 2646-17-5)

55 % or more but not more than 65 % of water

72 % (± 2 %) of mica (CAS RN 12001-26-2), and

28 % (± 2 %) of titanium dioxide (CAS RN 13463-67-7)

30 % by weight or more, but not more than 50 % of silver, and

8 % by weight or more, but not more than 17 % of palladium

of a thickness of 0,3 μm or more but not more than 10 μm, and

coated with titanium dioxide (CAS RN 13463-67-7) or iron oxide (CAS RN 18282-10-5)

0,1 % or more but not more than 20 % of alkoxygroups containing siloxane polymer with alkyl or aryl substituents

75 % or more of an organic solvent containing one or more of propyleneglycolethylether (CAS RN 1569-02-4), propylene glycol mono methylether acetate (CAS RN 108-65-6) or propyleneglycol propylether (CAS RN 1569-01-3)

(65 ± 10) % of γ-butyrolactone,

(30 ± 10) % of polyamide resin,

(3,5 ± 1,5) % of naphthoquinone ester derivative, and

(1,5 ± 0,5) % of arylsilicic acid

styrene

alkoxystyrene

alkylacrylates

consisting of a polyester polymer and a dispersion of silver (CAS RN 7440-22-4) and silver chloride (CAS RN 7783-90-6) in methyl propyl ketone (CAS RN 107-87-9),

with a total solid content by weight of 55 % or more, but not more than 57 %, and

with a specific density of 1,40 g/cm3 or more, but not more than 1,60 g/cm3,

1 % or more, but not more than 10 % of amorphous silicon dioxide, or

3,8 % or more of dye C.I. Solvent Black 7 in organic solvents,

wax,

a vinyl-based polymer, and

a colouring agent,

15 % or more but not more than 60 % of styrene butadiene copolymers or styrene isoprene copolymers, and

10 % or more but not more than 30 % of pinene polymers or pentadiene copolymers,

Methyl ethyl ketone (CAS RN 78-93-3),

Heptane (CAS RN 142-82-5), and

Toluene (CAS RN 108-88-3) or light aliphatic solvent naphta (CAS RN 64742-89-8)

an enzyme concentration of 6,0 U/ml or more, but not more than 7,4 U/ml,

a concentration by weight of sodium azide (CAS RN 26628-22-8) of not more than 0,09 %, and

a pH value of 6,5 or more, but not more than 8,5

by weight not more than 12 % of diazooxonaphthalenesulphonic acid ester

phenolic resins

phenolic or acrylic resins,

a maximum 2 % by weight of light sensitive acid precursor,

acrylate polymers,

methacrylate polymers,

derivatives of styrene polymers,

not more than 10 % by weight of naphthoquinonediazide esters,

2 % or more but not more than 35 % by weight of copolymers of hydroxystyrene,

not more than 7 % by weight of epoxy-containing derivatives,

55 % or more but not more than 75 % by weight of xylene, and

12 % or more but not more than 18 % by weight of ethylbenzene

20 % or more but not more than 45 % of copolymers of acrylates and/or methacrylates and hydroxystyrene derivatives,

25 % or more but not more than 50 % of organic solvent containing at least ethyl lactate and/or propylene glycolmethylether acetate,

5 % or more but not more than 30 % of acrylates,

not more than 12 % of a photoinitiator

not more than 5 % of photoacid generator,

2 % or more but not more than 50 % of phenolic resins, and

not more than 7 % of epoxy-containing derivatives,

styrene acrylate/butadiene copolymer

either carbon black or an organic pigment

whether or not containing polyolefin or amorphous silica

an average particle size of 2,5 μm or more but not more than 26,5 μm,

an iron content of less than 40 ppm,

a copper content of less than 5 ppm,

a nickel content of less than 5 ppm,

an average surface area (N2-atmosphere) of 1,2 m2/g or more but not more than 20,4 m2/g, and

a magnetic metal impurity of less than 3 ppm

an average particle size of 2,5 μm or more but not more than 26,5 μm,

an iron content of less than 40 ppm,

a copper content of less than 5 ppm,

a nickel content of less than 5 ppm,

an average surface area (N2-atmosphere) of 1,2 m2/g or more but not more than 20,4 m2/g, and

a magnetic metal impurity of less than 3 ppm

a diameter of 2 mm or more but not more than 3 mm, and

a Butane Working Capacity of 5 g butane/100 ml or more (as determined by the ASTM D 5228 method),

containing by weight 50 % or more but not more than 75 % of rosin esters,

with an acid value of not more than 25,

Bacillus thuringiensis Berliner subsp. aizawai and kurstaki, or

Bacillus thuringiensis subsp. kurstaki, or

Bacillus thuringiensis subsp. israelensis, or

Bacillus thuringiensis subsp. aizawai, or

Bacillus thuringiensis subsp. tenebrionis

24 % or more but not more than 26 % of pyrithione zinc (INN), or

39 % or more but not more than 41 % of pyrithione zinc (INN)

30 % or more of tepraloxydim (ISO), and

not more than 70 % of a petroleum fraction consisting of aromatic hydrocarbons

38,8 % or more but not more than 41,2 % of Gibberellin A3, or

9,5 % or more but not more than 10,5 % of Gibberellin A4 and A7

1,88 % or more but not more than 2,00 % of benzyl(purin-6-yl)amine

1,8 % of sodium para-nitrophenolate,

1,2 % of sodium ortho-nitrophenolate,

0,6 % of sodium 5-nitroguaiacolate,

3 % or more but not more than 3,6 % of 1-methylcyclopropene with a purity more than 96 %, and

containing less than 0,05 % of each impurity of 1-chloro-2-methylpropene and 3-chloro-2-methylpropene,

55 % or more of Gibberellin A4,

1 % or more but not more than 35 % of Gibberellin A7,

90 % or more of Gibberellin A4 and Gibberellin A7 combined,

not more than 10 % of a combination of water and other naturally occurring Gibberellins,

0,55 % or more but not more than 2,50 % of 1-methylcyclopropene (1-MCP) (CAS RN 3100-04-7) with a minimum purity of 96 % or more, and

less than 0,05 % of each of the two impurities, 1-chloro-2-methylpropene (CAS RN 513-37-1) and 3-chloro-2-methylpropene (CAS RN 563-47-3),

1,3-Dichloro-5,5-dimethylimidazolidine-2,4-dione (CAS RN 118-52-5),

1,3-Dibromo-5,5-dimethylimidazolidine-2,4-dione (CAS RN 77-48-5),

1-Bromo,3-chloro-5,5-dimethylimidazolidine-2,4-dione (CAS RN 16079-88-2), and

1-Chloro,3-bromo-5,5-dimethylimidazolidine-2,4-dione (CAS RN 126-06-7)

70 % or more, but not more than 90 % of tin

not more than 10 % of one or more metals of silver, copper, bismuth, zinc, or indium

4,9 % of 1,2,4-trimethyl-benzene,

4,9 % of naphthalene, and

0,5 % of 1,3,5-trimethyl-benzene

o-amino polyisobutylenephenol (CAS RN 78330-13-9),

more than 30 % by weight but not more than 50 % by weight of mineral oils,

esters of polyisobutenyl succinic acid and pentaerythritol (CAS RN 103650-95-9),

35 % or more but not more than 55 % by weight of mineral oils, and

with a chlorine content of not more than 0,05 % by weight,

borated magnesium (C16-C24) alkylbenzene sulphonates, and

mineral oils,

containing polyisobutene succinimide derived from reaction products of polyethylenepolyamines with polyisobutenyl succinic anhydride (CAS RN 147880-09-9),

containing 35 % or more but not more than 55 % by weight of mineral oils,

with a chlorine content by weight of not more than 0,05 %,

having a total base number of less than 15,

Calcium salt of beta-aminocarbonyl alkylphenol (reaction product Mannich base of alkylphenol),

40 % or more but not more than 60 % by weight of mineral oils, and

having a total base number more than 120,

long chain alkyltoluene calcium sulphonates,

more than 30 % but not more than 50 % by weight of mineral oils, and

having a total base number of more than 310 but not more than 340,

a polyisobutylene succinimide based mixture, and

more than 30 % but not more than 50 % by weight of mineral oils,

a (C8-18) alkyl polymethacrylate copolymer with N-[3-(dimethylamino)propyl]methacrylamide, of an average molecular weight (Mw) of more than 10000 but not more than 20000, and

more than 15 %, but not more than 30 % by weight of mineral oils,

20 % or more by weight of an ethylene-propylene copolymer chemically modified by succinic anhydride groups reacted with 4-(4-nitrophenylazo)aniline and 3-nitroaniline, and

mineral oils,

calcium salts of heptylphenol reaction products with formaldehyde (CAS RN 84605-23-2), and

mineral oils,

a styrene-maleic anhydride copolymer esterified with C4-C20 alcohols, modified by aminopropylmorpholine, and

more than 50 % but not more than 75 % by weight of mineral oils,

overbased magnesium (C20-C24) alkylbenzenesulphonates (CAS RN 231297-75-9), and

by weight more than 25 % but not more than 50 % of mineral oils,

based on calcium C16-24 alkylbenzenesulphonates (CAS RN 70024-69-0),

containing mineral oils,

overbased calcium petroleum sulphonates (CAS 68783-96-0) with a sulphonate content by weight of 15 % or more, but not more than 30 %, and

by weight more than 40 % but not more than 60 % of mineral oils,

low base number calcium polypropylbenzenesulphonate (CAS RN 75975-85-8), and

by weight more than 40 % but not more than 60 % of mineral oils,

based on calcium polypropylenyl substituted benzenesulphonate (CAS RN 75975-85-8) with a content by weight of 25 % or more but not more than 35 %,

with a total base number (TBN) of 280 or more but not more than 320,

an overbased mixture of calcium petroleum sulphonates (CAS RN 61789-86-4) and synthetic calcium alkylbenzenesulphonates (CAS RN 68584-23-6 and CAS RN 70024-69-0) with a total sulphonate content by weight of 15 % or more, but not more than 25 %, and

by weight more than 40 % but not more than 60 % of mineral oils,

a polyisobutylene succinimide based mixture (CAS RN 160610-76-4), and

more than 35 % but not more than 50 % by weight of mineral oils,

containing polyisobutylene succinimide derived from reaction products of polyethylenepolyamines with polyisobutenyl succinic anhydride (CAS RN 84605-20-9),

containing mineral oils,

with a chlorine content by weight of 0,05 % or more but not more than 0,25 %,

with a total base number (TBN) of more than 20,

borated succinimide compounds (CAS RN 134758-95-5),

mineral oils, and

having a total base number (TBN) greater than 40,

Calcium (C10-C14) dialkylbenzenesulfonates,

more than 40 %, but not more than 60 % by weight of mineral oils,

a copolymer of 2-ethylhexyl acrylate and ethyl acrylate, and

more than 50 % but not more than 80 % by weight of mineral oils,

polyisobutylene aromatic polyamine succinimide,

more than 40 % but not more than 60 % by weight of mineral oils,

polyisobutene succinimide derived from reaction of polyethylenepolyamines with polyisobutenyl succinic anhydride (CAS RN 84605-20-9),

containing more than 31,9 % but not more than 43,3 % by weight of mineral oils,

not more than 0,05 % by weight chlorine, and

having a total base number (TBN) greater than 20,

containing more than 20 % or more but not more than 45 % by weight of mineral oils,

based on a mixture of branched dodecylphenol sulfide calcium salts, whether or not carbonated,

products from the reaction of branched heptyl phenol with formaldehyde, carbon disulphide and hydrazine (CAS RN 93925-00-9), and

more than15 % but not more than 28 % by weight of light aromatic petroleum naphtha solvent,

more than 70 % by weight of 2,5-bis(tert-nonyldithio)-[1,3,4]-thiadiazole (CAS RN 89347-09-1), and

more than 15 % by weight of 5-(tert-nonyldithio)- 1,3,4-thiadiazole-2(3H)-thione (CAS RN 97503-12-3),

polyisobutenyl succinic acid, and

more than 5 % and not more than 20 % by weight of mineral oils,

bis(2-ethylhexyl)-1,4-benzene dicarboxylate (CAS RN 6422-86-2)

more than 10 % but not more than 60 % by weight of dibutylterephthalate (CAS RN 1962-75-0)

α-[3-[3-(2H-Benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-ω-hydroxypoly(oxy-1,2-ethanediyl) (CAS RN 104810-48-2),

α-[3-[3-(2H-Benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-ω-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropoxy]poly (oxy-1,2-ethanediyl) (CAS RN 104810-47-1),

polyethylene glycol of a weight average molecular weight (Mw) of 300 (CAS RN 25322-68-3),

bis (1,2,2,6,6-pentamethyl-4-piperidyl)sebacate (CAS RN 41556-26-7), and

methyl-1,2,2,6,6-pentamethyl-4- piperidyl sebacate (CAS RN 82919-37-7)

25 % or more but not more than 50 % of a mixture of C15-18 tetramethylpiperidinyl esters (CAS RN 86403-32-9)

not more than 20 % of other organic compounds

on a carrier of polypropylene (CAS RN 9003-07-0)

80 % (± 10 %) by weight of 2-ethylhexyl 10-ethyl-4,4-dimethyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate, and

20 % (± 10 %) by weight of 2-ethylhexyl 10-ethyl-4-[[2-[(2-ethylhexyl)oxy]-2-oxoethyl]thio]-4-methyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate

2-(4,6-bis(2,4-dimethylphenyl)-1,3,5-triazin-2-yl)-5-(octyloxy)-phenol (CAS RN 2725-22-6), and

either N,N′-bis(1,2,2,6,6-pentamethyl-4-piperidinyl)-1,6-hexanediamine, polymer with 2,4- dichloro-6-(4-morpholinyl)-1,3,5-triazine (CAS RN 193098-40-7), or

N,N′-bis(2,2,6,6-tetramethyl-4-piperidinyl)-1,6-hexanediamine, polymer with 2,4- dichloro-6-(4-morpholinyl)-1,3,5-triazine (CAS RN 82451-48-7)

2-ethylhexyl 10-ethyl-4,4-dimethyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate (CAS RN 57583-35-4),

2-ethylhexyl 10-ethyl-4-[[2-[(2-ethylhexyl)oxy]-2-oxoethyl]thio]-4-methyl-7-oxo-8-oxa-3,5-dithia-4-stannatetradecanoate (CAS RN 57583-34-3), and

2-ethylhexyl mercaptoacetate (CAS RN 7659-86-1)

branched and linear alkyl esters of 3-(2H-benzotriazolyl)-5-(1,1-dimethylethyl)-4-hydroxybenzenepropanoic acid (CAS RN 127519-17-9), and

1-methoxy-2-propyl acetate (CAS RN 108-65-6)

a hindered amine: N,N′-bis(1,2,2,6,6-pentamethyl-4-piperidinyl)-1,6-hexanediamine, polymer with 2,4-dichloro-6-(4-morpholinyl)-1,3,5-triazine (CAS RN 193098-40-7), and

either an o-hydroxyphenyl triazine UV light absorber, or

a chemically modified phenolic compound

69 % or more but not more than 71 % of 1-methoxypropan-2-ol,

29 % or more but not more than 31 % of 2-methoxy-1-methylethyl acetate

chromium trioxide (CAS RN 1333-82-0),

dichromium trioxide (CAS RN 1308-38-9),

in the form of solid spheres,

of a diameter of 4 mm or more but not more than 12 mm, and

consisting of a mixture of molybdenum oxide and other metal oxides, supported on silicon dioxide and/or aluminium oxide,

30 % or more but not more than 33 % of bis(4-(diphenylsulphonio)phenyl)sulphide bis(hexafluorophosphate) (CAS RN 74227-35-3), and

24 % or more but not more than 27 % of diphenyl(4-phenylthio)phenylsuphonium hexafluorophosphate (CAS RN 68156-13-8),

tetrahydrofuran complexes of magnesium chloride and titanium(III) chloride, and

silicon dioxide,

containing 6,6 % (± 0,6 %) by weight of magnesium, and

containing 2,3 % (± 0,2 %) by weight of titanium

25 % or more but not more than 27,5 % of bis[4-(diphenylsuphonio)phenyl]sulphide bis(hexafluoroantimonate) (CAS RN 89452-37-9), and

20 % or more but not more than 22,5 % of diphenyl(4-phenylthio)phenylsufonium hexafluoroantimonate (CAS RN 71449-78-0),

containing molybdenum oxide and other metal oxides in a silicon dioxide matrix,

in the form of hollow cylindrical solids of a length of 4 mm or more but not more than 12 mm,

4 % or more but not more than 10 % of titanium, and

10 % or more but not more than 20 % magnesium

35 % or more but not more than 60 % of eicosylbenzene,

25 % or more but not more than 50 % of docosylbenzene,

5 % or more but not more than 25 % of tetracosylbenzene

88 % or more but not more than 98 % of hexadecylnaphthalene

2 % or more but not more than 12 % of dihexadecylnaphthalene

industrial monocarboxylic fatty acids of heading 3823,

stearic acid of heading 3823,

stearic acid of heading 2915,

palmitic acid of heading 2915, or

animal feed preparations of heading 2309

industrial monocarboxylic fatty acids of heading 3823,

stearic acid of heading 3823,

stearic acid of heading 2915,

palmitic acid of heading 2915, or

animal feed preparations of heading 2309

25 % or more but not more than 50 % of diethyl carbonate (CAS RN 105-58-8)

25 % or more but not more than 50 % of ethylene carbonate (CAS RN 96-49-1)

10 % or more but not more than 20 % of lithium hexafluorophosphate (CAS RN 21324-40-3)

5 % or more but not more than 10 % of ethyl methyl carbonate (CAS RN 623-53-0)

1 % or more but not more than 2 % of vinylene carbonate (CAS RN 872-36-6)

1 % or more but not more than 2 % of 4-fluoro-1,3-dioxolane-2-one (CAS RN 114435-02-8)

Not more than 1 % of 1,5,2,4-Dioxadithiane 2,2,4,4-tetraoxide (CAS RN 99591-74-9)

60 % or more but not more than 75 % of Solvent naphtha (petroleum), heavy aromatic (CAS RN 64742-94-5),

15 % or more but not more than 25 % of 4-(4-nitrophenylazo)-2,6-di-sec-butyl-phenol (CAS RN 111850-24-9), and

10 % or more but not more than 15 % of 2-sec-butylphenol (CAS RN 89-72-5)

10 % or more but not more than 42 % of 2-(3-chloro-5-(trifluoromethyl)pyridin-2-yl)ethanamine (CAS RN 658066-44-5),

10 % or more but not more than 25 % of sulphuric acid (CAS RN 7664-93-9), and

0,5 % or more but not more than 2,9 % of methanol (CAS RN 67-56-1)

85 % or more but not more than 99 % of polyethylene glycol ether of butyl 2-cyano 3-(4-hydroxy-3-methoxyphenyl) acrylate, and

1 % or more but not more than 15 % of polyoxyethylene (20) sorbitan trioleate

1 % or more but not more than 84 % of caesium formate (CAS RN 3495-36-1),

1 % or more but not more than 76 % of potassium formate (CAS RN 590-24-1), and

whether or not containing not more than 9 % of additives

on a support of mineral wax, whether or not modified chemically, or

in the form of a solution in an organic solvent

trioctylphosphine oxide (CAS RN 78-50-2),

dioctylhexylphosphine oxide (CAS RN 31160-66-4),

octyldihexylphosphine oxide (CAS RN 31160-64-2), and

trihexylphosphine oxide (CAS RN 3084-48-8)

either diethylene glycol, dodecandioic acid and ammonia water,

or N,N-dimethylformamide,

or γ-butyrolactone,

or silicon oxide,

or ammonium hydrogen azelate,

or ammonium hydrogen azelate and silicon oxide,

or dodecandioic acid, ammonia water and silicon oxide,

a mixture of esters of phosphoric acid obtained from the reaction of phosphoric anhydride with 4-(1,1-dimethylpropyl) phenol and copolymers of styrene-allyl alcohol (CAS RN 84605-27-6), and

30 % or more but not more than 35 % by weight of isobutyl alcohol

89 % or more but not more than 98,9 % of 1,2,3-trideoxy-4,6:5,7-bis-O-[(4-propylphenyl)methylene]-nonitol

0,1 % or more but not more than 1 % of colourants

1 % or more but not more than 10 % of fluoropolymers

20 % (± 1 %) ((3-(sec-butyl)-4-(decyloxy)phenyl)methanetriyl) Tribenzene (CAS RN 1404190-37-9),

10 % (± 5 %) 2-sec-Butylphenol (CAS RN 89-72-5),

64 % (± 7 %) Solvent naphtha (petroleum), heavy aromatic (CAS RN 64742-94-5), and

6 % (± 1,0 %) Naphthalene (CAS RN 91-20-3)

80 % or more but not more than 92 % of Bisphenol-A bis(diphenyl phosphate) (CAS RN 5945-33-5),

7 % or more but not more than 20 % oligomers of Bisphenol-A bis(diphenyl phosphate), and

not more than 1 % triphenyl phosphate (CAS RN 115-86-6)

74 % or more but not more than 90 % by weight of (S)-α-hydroxy-3-phenoxy-benzeneacetonitrile (CAS RN 61826-76-4), and

10 % or more but not more than 26 % by weight of toluene (CAS RN 108-88-3)

either an aluminium-alkyl compound, or

an organic complex of tungsten, or

an organic complex of molybdenum

85 % or more of zinc diacrylate (CAS RN 14643-87-9),

not more than 5 % of 2,6-di-tert-butyl-alpha-dimethylamino-p-cresol (CAS RN 88-27-7), and

not more than 10 % of zinc stearate (CAS RN 557-05-1)

not more than 20 % of disodium sulphate, and

not more than 10 % of sodium chloride

70 % or more, but not more than 90 % of (S)-indoline-2-carboxylic acid (CAS RN 79815-20-6), and

10 % or more, but not more than 30 % of o-chlorocinnamic acid (CAS RN 3752-25-8)

40 % or more but not more than 88 % of sitosterols,

20 % or more but not more than 63 % of campesterols,

14 % or more but not more than 38 % of stigmasterols,

not more than 13 % brassicasterols, and

not more than 5 % sitostanols

75 % or more of sterols,

not more than 25 % of stanols,

C,C′-azodi(formamide) (CAS RN 123-77-3),

magnesium oxide (CAS RN 1309-48-4), and

zinc bis(p-toluene sulphinate) (CAS RN 24345-02-6),

60 % or more, but not more than 80 % of sitosterols,

less than 15 % of campesterols,

less than 5 % of stigmasterols, and

less than 15 % of betasitostanols

20 % or more but not more than 30 % of cerium oxide (CAS RN 1306-38-3),

2 % or more but not more than 10 % of lanthanum oxide (CAS RN 1312-81-8),

10 % or more but not more than 15 % of yttrium oxide (CAS RN 1314-36-9), and

not more than 65 % of zirconium oxide (CAS RN 1314-23-4) including natural occurring hafnium oxide

a particle size of less than 10 μm,

a purity by weight of more than 98 %

52 % or more but not more than 76 % of iron(III)oxide,

13 % or more but not more than 42 % of manganese oxide, and

2 % or more but not more than 22 % of zinc oxide

either 5 % or more of barium, neodymium or magnesium and 15 % or more of titanium,

or 30 % or more of lead and 5 % or more of niobium,

ferrite (Iron oxide) (CAS RN 1309-37-1)

manganese oxide (CAS RN 1344-43-0)

magnesium oxide (CAS RN 1309-48-4)

styrene acrylate copolymer

either 1,6mm or more but not more than 3,4 mm,

or 4mm or more but not more than 6 mm

28 % or more but not more than 51 % of talc (CAS RN 14807-96-6)

30,5 % or more but not more than 48 % of silicon dioxide (quartz) (CAS RN 14808-60-7)

17 % or more but not more than 26 % of aluminium oxide (CAS RN 1344-28-1)

1 % or more but not more than 40 % of molybdenum oxide,

10 % or more but not more than 50 % of nickel oxide,

30 % or more but not more than 70 % of tungsten oxide

with a crystalline structure,

with a content of fused magnesia-alumina spinel and with admixtures of silicate phases and aluminates, at least 75 % by weight of which consists of fractions with a grain size of 1-3 mm and at most 25 % consists of fractions with a grain size of 0-1 mm

64 % or more, but not more than 74 % by weight of amorphous silica (CAS RN 7631-86-9),

25 % or more, but not more than 35 % by weight of butanone (CAS RN 78-93-3), and

not more than 1 % by weight of 3-(2,3-epoxypropoxy)propyltrimethoxysilane (CAS RN 2530-83-8)

0,1 % or more but not more than 1 % of platinum, and

0,5 % or more but not more than 5 % of ethylaluminium dichloride (CAS RN 563-43-9)

65 % or more but not more than 75 % of C12 FAME,

21 % or more but not more than 28 % of C14 FAME,

4 % or more but not more than 8 % of C16 FAME,

50 % or more but not more than 58 % of C8-FAME

35 % or more but not more than 50 % of C10-FAME

a melt flow rate (MFR 190 °C/2,16 kg) of 16 g/10 min or more, but not more than 24 g/10 min, and

a density (ASTM D 1505) of 0,922 g/cm3 or more, but not more than 0,926 g/cm3, and

a vicat softening temperature of min. 94 °C

10 % or more but not more than 20 % by weight of octene,

a melt flow ratio of 9,0 or more, but not more than 10,0 (using ASTM D1238 10,0/2,16),

a melt index (190 °C/2,16 kg) of 0,4 g / 10 min or more but not more than 0,6 g/10 min,

a density of 0,909 g/cm3 or more, but not more than 0,913 g/cm3 using ASTM D4703,

a gel area per 24,6 cm3 of not more than 20 mm2, and

an anti-oxidant level of not more than 240 ppm

more than 10 % but not more than 20 % by weight of copolymer,

a melt flow rate (MFR 190 °C/2,16 kg) of 0,7 g/10 min or more but not more than 0,9 g/10 min, and

a density (ASTM D4703) of 0,911 g/cm3 or more, but not more than 0,913 g/cm3,

with a specific gravity of 0,862 or more, but not more than 0,865,

able to stretch to at least 200 % its original length,

with a hysteresis of 50 % (± 10 %),

with permanent deformation of not more than 20 %,

an acrylic acid content of 18,5 % or more but not more than 49,5 % by weight (ASTM D4094), and

a melt flow rate of 14g/10 min (MFR 125 °C/2,16 kg, ASTM D1238) or more

an acrylic acid content of 6 % or more but not more than 50 % by weight, and

a melt flow rate of 1g/10 min or more at 190 °C/2,16 kg (measured using ASTM D1238)

80 % or more, but not more than 94 % of chlorinated polyethylene (CAS RN 64754-90-1), and

6 % or more, but not more than 20 % of styrene-acrylic copolymer (CAS RN 27136-15-8)

of a melting point of more than 150 °C (as determined by the ASTM D 3417 method),

of a heat of fusion of 15 J/g or more but not more than 70 J/g,

of an elongation at break of 1000 % or more (as determined by the ASTM D 638 method),

of a tensile modulus of 69 MPa or more but not more than 379 MPa (as determined by the ASTM D 638 method)

of a tensile strength: of 32-60 MPa (as determined by the ASTM D638 method),

of a flexural strength of 50-90 MPa (as determined by the ASTM D790 method),

of a Melt Flow Rate (MFR) at 230 °C/ 2,16 kg of 5-15 g/10 min (as determined by the ASTM D1238 method),

with 40 % or more but not more than 80 % by weight of polypropylene,

with 10 % or more but not more than 30 % by weight of glass fibre,

with 10 % or more but not more than 30 % by weight of mica

a copolymer of propylene and ethylene, and

21 % (± 3 %) by weight of polystyrene

a flashpoint of 250 °C or more,

a viscosity index of 150 or more,

of a number average molecular weight (Mn) of 650 or more

liquid at room temperature

obtained by cationic polymerisation of C-5 alkenes monomers

with a number average molecular weight (Mn) of 370 (± 50)

with a weight average molecular weight (Mw) of 500 (± 100)

a melting point of 268 °C or more but not more than 272 °C,

a setting point of 232 °C or more but not more than 247 °C,

whether or not containing additives and filling material

78 (± 4 %) of styrene,

9 (± 2 %) of n-butyl acrylate,

11 (± 3 %) of n-butyl methacrylate,

1,5 (± 0,7 %) of methacrylic acid, and

0,01 % or more but not more than 2,5 % of polyolefinic wax

83 ± 3 % styrene,

7 ± 2 % n-butyl acrylate,

9 ± 2 % n-butyl methacrylate, and

0,01 % or more but not more than 1 % of polyolefinic wax

82 ± 6 % styrene,

13,5 ± 3 % n-butyl acrylate,

1 ± 0,5 % methacrylic acid, and

0,01 % or more but not more than 8,5 % of polyolefinic wax

86 % or more but not more than 90 % of styrene-acrylic-copolymer, and

9 % or more but not more than 11 % of fatty acid ethoxylate (CAS RN 9004-81-3)

74 % (± 4 %) styrene,

24 % (± 2 %) n-butylacrylate, and

0,01 % or more but not more than 2 % methacrylic acid

25 % or more but not more than 26 % of styrene-acrylic-copolymer, and

5 % or more but not more than 6 % of glycol

75 % (± 7 %) styrene, and

25 % (± 7 %) methylmethacrylate

minimum 65 % styrene,

maximum 25 % divinylbenzene,

45 % or more but not more than 65 % of polymers of styrene

35 % or more but not more than 45 % of poly(phenylene ether)

not more than 10 % of other additives

metallic or pearlescent with a visual angular metamerism caused by at least 0,3 % flake-based pigment

fluorescent, as characterized by emitting light during absorption of ultraviolet radiation

bright white, as characterized by L* not less than 92 and b* not more than 2 and a* between – 5 and 7 on the CIELab colour scale

a degree of polymerisation of 1000 (± 300) monomer units,

a coefficient of heat transmission (K-value) of 60 or more, but not more than 70,

a volatile material content of less than 2,00 % by weight,

a sieve non-passing fraction at a mesh width of 120 μm of not more than 1 % by weight,

87 % or more but not more than 92 % of vinyl chloride,

2 % or more but not more than 9 % of vinyl acetate, and

1 % or more but not more than 8 % of vinyl alcohol,

9,5 % or more but not more than 13 % of acetyl groups evaluated as vinyl acetate, and

5 % or more but not more than 6,5 % of hydroxy groups evaluated as vinyl alcohol

a viscosity of not more than 50000 Pa · s at 120 °C as determined by the test method ASTM D 3835,

a weight average molecular weight (Mw) of more than 500000 but not more than 1200000 according to the Gel Permeation Chromatography (GPC) test,

a residual monomer content of less than 1 %

chloromethyl vinyl ether,

chloroethyl vinyl ether,

chloromethylstyrene,

vinyl chloroacetate,

methacrylic acid,

butenedioic acid monobutyl ester,

75 % or more but not more than 85 % of polyacrylamide, and

15 % or more but not more than 25 % of polyethylene glycol

more than 10 % but not more than 15 % of ethanol, and

more than 7 % but not more than 11 % of a reaction product of poly(epoxyalkylmethacrylate-co-divinylbenzene) with a glycerol derivative

33 % or more but not more than 37 % of butyl methacrylate - methacrylic acid copolymer,

24 % or more but not more than 28 % of propylene glycol, and

37 % or more but not more than 41 % of water

α-[3-[3-(2H-Benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-ω-hydroxypoly(oxy-1,2-ethanediyl) (CAS RN 104810-48-2), and

α-[3-[3-(2H-Benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-ω-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropoxy]poly(oxy-1,2-ethanediyl) (CAS RN 104810-47-1)

48 % or more but not more than 52 % of propylene oxide, and

48 % or more but not more than 52 % of butylene oxide

5 % or more but not more than 15 % of a copolymer of glycerol, propylene oxide and ethylene oxide (CAS RN 9082-00-2), and

85 % or more but not more than 95 % of a copolymer of sucrose, propylene oxide and ethylene oxide (CAS RN 26301-10-0)

with a glasstransitiontemperature of 210 °C,

with a weight average molecular weight (Mw) of 35000 or more but not more than 80000,

with an inherent viscosity of 0,2 or more but not more than 0,6 dl/gram

containing by weight more than 2 % phosphoros calculated on the solid content, chemically bound in the epoxide resin,

not containing any hydrolysable chloride or containing less than 300 ppm hydrolysable chloride, and

containing solvents,

containing by weight 21 % or more of brome,

not containing any hydrolysable chloride or containing less than 500 ppm hydrolysable chloride, and

containing solvents

65 % or more but not more than 75 % of silicon dioxide (CAS RN 60676-86-0), and

none or not more than 0,5 % of carbon black (CAS RN 1333-86-4)

containing by weight 12 % or more but not more than 26 % of a copolymer of isophthaloyl chloride, terephthaloyl chloride and resorcinol,

with p-cumylphenol endcaps, and

with a weight average molecular weight (Mw) of 29900 or more but not more than 31900

with a specific gravity of 1,23 or more but not more than 1,27 at 23 °C, and

containing not more than 10 % by weight of other modifiers or additives

phthalic acid isomers and/or aliphatic dicarboxylic acids,

aliphatic diols, and

fatty acid end-caps,

a hydroxyl number of 120 mg KOH or more but not more than 350 mg KOH,

a viscosity at 25 °C of 2000 cPs or more but not more than 8000 cPs, and

an acid value less than 10 mg KOH/g

1,3-benzenedimethanamine (CAS RN 1477-55-0), and

adipic acid (CAS RN 124-04-9),

60 % or more but not more than 75 % of melamine resin (CAS RN 9003-08-1),

15 % or more but not more than 25 % of silicon dioxide (CAS RN 14808-60-7 or 60676-86-0),

5 % or more but not more than 15 % of cellulose (CAS RN 9004-34-6), and

1 % or more but not more than 15 % of phenolic resin (CAS RN 25917-04-8)

60 % or more of two-functional acrylated polyurethane oligomers, and

30 % (± 8 %) of mono-functional and tri-functional (metha) acrylates, and

10 % (± 3 %) of hydroxyl functionalized mono-functional (metha) acrylates

14 % or more but not more than 18 % of ethoxylated polyurethane modified with hydrophobic groups,

3 % or more but not more than 5 % of enzymatically modified starch, and

77 % or more but not more than 83 % of water

16 % or more but not more than 20 % of ethoxylated polyurethane modified with hydrophobic groups,

19 % or more but not more than 23 % of diethylene glycol butyl ether, and

60 % or more but not more than 64 % of water

34 % or more but not more than 36 % of ethoxylated polyurethane modified with hydrophobic groups,

37 % or more but not more than 39 % of propylene glycol, and

26 % or more but not more than 28 % of water

10 % or more, 2-hydroxy-3-[3-[1,3,3,3-tetramethyl-1-[(trimethylsilyl)oxy] disiloxanyl] propoxy] propyl-2-methyl-2-propenoate (CAS RN 69861-02-5)and

10 % or more, α-Butyldimethylsilyl- ω -3-[(2-methyl-1-oxo-2-propen-1-yl)oxy]propyl-terminated silicone polymer (CAS RN 146632-07-7)

30 % or more, α -Butyldimethylsilyl- ω -(3-methacryloxy-2-hydroxypropyloxy)propyldimethylsilyl-polydimethylsiloxane (CAS RN 662148-59-6), and

10 % or more, N,N – Dimethylacrylamide (CAS RN 2680-03-7)

55 % or more but not more than 65 % of vinyl terminated polydimethylsiloxane (CAS RN 68083-19-2),

30 % or more but not more than 40 % of dimethylvinylated and trimethylated silica (CAS RN 68988-89-6), and

1 % or more but not more than 5 % of silicic acid, sodium salt, reaction products with chlorotrimethylsilane and isopropyl alcohol (CAS RN 68988-56-7)

an iodine value of more than 120, and

a Gardner Colour of more than 10 for the pure product, or

a Gardner Colour of more than 8 for a 50 % solution by weight in toluene (as determined by the ASTM method D6166)

83 % or more by weight of 3a,4,7,7a-tetrahydro-4,7-methanoindene (dicyclopentadiene),

a synthetic rubber,

whether or not containing by weight 7 % or more of tricyclopentadiene

either an aluminium-alkyl compound, or

an organic complex of tungsten, or

an organic complex of molybdenum

Cyanic acid, C,C′-((1-methylethylidene)di-4,1-phenylene) ester, homopolymer (CAS RN 25722-66-1),

1,3-Bis(4-cyanophenyl)propane (CAS RN 1156-51-0),

in a solution of butanone (CAS RN 78-93-3) with a content of less than 50 % by weight

titanium dioxide

poly(methyl methacrylate)

calcium carbonate

binding agents

polyamide-6 or poly(epoxy anhydride)

7 % or more but not more than 9 % of polytetrafluorethylene if present

10 % or more but not more than 25 % of inorganic fillers

coated on one side with an acrylic thermal release adhesive that debonds at temperatures of 90 °C or more but not more than 200 °C, and a polyester liner, and

on the other side not coated or coated with an acrylic pressure sensitive adhesive or with an acrylic thermal release adhesive that debonds at temperatures of 90 °C or more but not more than 200 °C, and a polyester liner

with a thickness of 100 μm or more,

an elongation at break of not more than 100 %,

coated on one side with a pressure sensitive silicon adhesive

with a gloss of more than 30 degrees according to ASTM D2457,

whether or not covered on one side with a protective poly(ethyleneterephthalate) film, and on the other side with a pressure sensitive adhesive with channels and a release liner

of a thickness of 100 μm or more,

coated on one side with an acrylic pressure sensitive or UV-sensitive adhesive and a polyester or polypropylene liner

of a polycarbonate or acrylic polymer film embossed on one side in a regular shaped pattern,

covered on one or both sides with one or more layers of plastic or metallisation, and

whether or not covered on one side with a self-adhesive layer and a release sheet

a layer of an acrylic resin with imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use,

a layer of an acrylic resin having embedded glass beads,

a layer of an acrylic resin hardened by a melamine cross-linking agent,

a metal layer,

an acrylic adhesive, and

a release film

self-adhesive on one side,

of a total thickness of 0,025 mm or more, but not more than 0,09 mm,

of a total width of 60 mm or more, but not more than 1110 mm,

whether or not containing a watermark,

with or without an application tape coated on one side with an adhesive,

a layer of acrylic or vinyl polymer,

a layer of poly(methyl methacrylate) or polycarbonate containing microprisms,

a layer of metallisation,

an adhesive layer, and

a release sheet,

whether or not containing an additional layer of polyester

a copolymer of acrylic resin,

polyurethane,

a metallised layer with, on one side, laser imprints against counterfeiting, alteration or substitution of data or duplications, or an official mark for an intended use,

glass microspheres, and

an adhesive layer, with a release liner on one or both sides

coated on one side with an acrylic UV-sensitive adhesive and a liner

of a total thickness of 65 μm or more without release liner

free from impurities or faults,

coated on one side with an acrylic pressure sensitive adhesive and a protective liner, and on the other side with an antistatic layer of ionic organic choline compound,

whether or not with a printable dust-proof layer of modified long chain alkyl organic compound,

with a total thickness without the liner of 54 μm or more but not more than 64 μm, and

a width of more than 1295 mm but not more than 1305 mm

with a thickness of 50 μm or more but not more than 155 μm,

with a width of 6,30 mm or more but not more than 585 mm,

an elongation at break of not more than 200 %, and

coated on one side with a pressure sensitive silicone adhesive with a thickness of not more than 40 μm

consisting of an epoxy acrylate layer embossed on one side in a regular shaped pattern,

covered on both sides with one or more layers of plastic material, and

covered on one side with an adhesive layer and a release sheet

a layer of polyurethane containing glass micro beads,

a layer of poly(ethylene vinyl acetate),

an adhesive layer, and

a release sheet

one side partly printed whereby part of the printing either gives information about the meaning of LED′s visible at the unprinted areas, or marks those points which must be touched to operate the system,

the other side partly covered with an adhesive layer,

both sides covered with a release liner, and

with dimensions of not more than 14 cm × 2,5 cm,

an adhesive layer based on synthetic rubber with a thickness of 8 μm or more but not more than 17 μm,

a polyolefin layer with a thickness of 28 μm or more but not more than 40 μm, and

a non-silicone release layer with a thickness below 1 μm

a polymer layer

an adhesive layer

a release liner, on one side embossed, containing oblate spheres,

each layer containing a mixture of polypropylene and polyethylene,

containing not more than 3 % by weight of other polymers,

whether or not containing titanium dioxide in the core layer,

coated with an acrylic pressure sensitive adhesive, and

with a release liner,

of an overall thickness of not more than 110 μm

a polyurethane layer,

a glass microspheres layer,

a metallised aluminium layer, and

an adhesive, covered on one or both sides with a release liner,

whether or not a poly(vinyl chloride) layer,

a layer whether or not incorporating security imprints against counterfeiting, alteration or substitution of data or duplication, or an official mark for an intended use

for protection against ultraviolet or infra-red heat radiation, to be affixed to windows, or

for equal transmission and distribution of light, intended for LCD modules

of polymers of ethylene

having a gravity of 0,94 g/cm3 or more

of a thickness of 0,019 mm ± 0,003 mm

with permanent graphics consisting of two different alternating designs whose individual length is 525 mm or more

is repetitive and equally spaced along the length of the film

is equally and visibly aligned when viewed from the back or front of the film

consisting of a tri-layer barrier with a core layer of ethylene vinyl alcohol covered on either side with a layer of polyamide, covered on either side with at least one layer of polyethylene,

having a total thickness of 55 μm or more,

having a diameter of 500 mm or more but not more than 600 mm

a raised relief surface with embossed undulations, and

a thickness of more than 0,125 mm

with the thickness of not more than 0,1 mm,

printed on both sides with specialised coatings to allow banknote security printing

a tensile strength in the machine direction of 120 MPa or more but not more than 270 MPa, and

a tensile strength in the transverse direction of 10 MPa or more but not more than 40 MPa,

a thickness of 55 μm or more but not more than 97 μm,

a tensile modulus in the machine direction of 0,30 GPa or more but not more than 1,45 GPa, and

a tensile modulus in the transverse direction of 0,20 GPa or more but not more than 0,70 GPa

each layer containing a mixture of polypropylene and polyethylene,

containing not more than 3 % by weight of other polymers,

whether or not containing titanium dioxide in the core layer,

of an overall thickness of not more than 70 μm

containing by weight 45 % or more of fillers

on a support

with a thickness of 0,335 mm or more but not more than 0,365 mm, and

coated with a gold layer with a thickness of 0,03 μm or more but not more than 0,06 μm

only dyed in the mass, or

dyed in the mass and metallised on one side

coated on both sides with a layer of epoxy acrylic resin,

of a total thickness of 37 μm (± 3 μm)

of a thickness of not more than 20 μm,

coated on at least one side with a gas barrier layer consisting of a polymeric matrix in which silica or aluminium oxide has been dispersed and of a thickness of not more than 2μm

coated on both sides with layers of organic substances on the basis of acryl of a thickness of 7 nm or more but not more than 80 nm,

with a surface tension of 36 Dyne/cm or more but not more than 39 Dyne/cm,

with a light transmission of more than 93 %,

with a haze value of not more than 1,3 %,

with a total thickness of 10 μm or more but not more than 350 μm,

with a width of 800 mm or more but not more than 1600 mm

composed of more than 85 % by weight of poly(lactic acid) and not more than 10,50 % by weight of modified poly(lactic acid) based polymer, poly-glycol ester and talc,

having a thickness of 20 μm or more but not more than 120 μm,

biodegradable and compostable (as determined by the method EN 13432)

composed of more than 80 % by weight of poly(lactic acid) and not more than 15,75 % by weight of additives of modified poly(lactic acid),

having a thickness of 45 μm or more but not more than 50 μm,

biodegradable and compostable (as determined by the method EN 13432)

containing by weight 26 % or more but not more than 30 % of triethyleneglycol bis(2-ethyl hexanoate) as a plasticiser,

with a thickness of 0,73 mm or more but not more than 1,50 mm

a visible light transmission of 50 % or more,

coated on one or both sides with a layer of poly(vinyl butyral) but not coated with an adhesive or any other material except poly(vinyl butyral),

a total thickness of not more than 0,2 mm without taking the presence of poly(vinyl butyral) into account and a thickness of poly(vinyl butyral) of more than 0,2 mm

poly (tetramethylene ether glycol),

bis (4-isocyanotocyclohexyl) methane,

1,4-butanediol or 1,3-butanediol,

with a thickness of 0,25 mm or more but not more than 5,0 mm,

embossed with a regular pattern on one surface, and

covered with a release sheet

with a gloss of more than 90 degrees according to ASTM D2457

covered on the metallised side with a heat bonding adhesive layer consisting of polyethylene/polypropylene copolymer

covered on the other side with a protective poly(ethylene terephthalate) film

with a total thickness of more than 204 μm but not more than 244 μm

a width of 1640 mm (± 10 mm),

a gloss of 3,3 degrees or more but not more than 3,8 (as determined by the method ASTM D2457),

a surface roughness of 1,9 Ra or more but not more than 2,8 Ra (as determined by the method ISO 4287),

a thickness of more than 365 μm but not more than 760 μm,

a hardness of 90 (± 4) (as determined by the method: Shore A (ASTM D2240)),

an elongation to break of 470 % (as determined by the method: EN ISO 527)

microspheres with a coating of metal, whether or not alloyed with gold,

an adhesive layer,

with a protective layer of silicone or poly(ethylene terephthalate) on one side,

with a protective layer of poly(ethylene terephthalate) on the other side, and

with a width of 5 cm or more but not more than 100 cm,

with a length of not more than 2000 m

a width of more than 900 mm but not more than 1016 mm,

a matt finish,

a thickness of 0,43 mm (± 0,03 mm),

an elongation to break of 420 % or more but not more than 520 %,

a tensile strength of 55 N/mm2 (± 3) (as determined by the method EN ISO 527)

a hardness of 90 (± 4) (as determined by the method: Shore A [ASTM D2240]),

wrinkle inside (waves) of 6,35 mm,

a flatness of 0,025 mm

a thickness of 50 μm,

a melting point of 260 °C, and

a specific gravity of 1,75 (ASTM D792),

a thickness of 0,010 mm or more but not more than 0,80 mm,

a width of 1219 mm or more but not more than 1575 mm, and

a melting point of 252 °C (measured according ASTM D-3418)

with a thickness of 2,29 mm (± 0,25 mm),

surface-treated with a foraminous adhesion promoter, and

laminated to a polyester film and a layer of textile material

polyamide-6 or poly(epoxy anhydride)

7 % or more but not more than 9 % of polytetrafluorethylene if present

10 % or more but not more than 25 % of inorganic fillers

30 % or more but not more than 60 % of a microporous polypropylene layer (CAS RN 9003 07-0),

20 % or more but not more than 40 % of a microporous polyethylene layer (CAS RN 9002-88-4), and

20 % or more but not more than 40 % of a boehmite layer/coating (CAS RN 1318-23-6),

a width of 98 mm or more but not more than 170 mm,

a thickness of 15 μm or more but not more than 36 μm,

a total thickness of more than 0,05 mm but not more than 0,20 mm,

a water entry pressure between 5 and 200 kPa according to ISO 811, and

an air permeability of 0,08 cm3/cm2/s or more according to ISO 5636-5

one microporous polyethylene layer between two microporous polypropylene layers and whether or not containing a coating of aluminium oxide on both sides,

a width of 65 mm or more but not more than 170 mm,

a total thickness of 0,01 mm or more but not more than 0,03 mm,

a porosity of 0,25 or more but not more than 0,65

a width of 1600 mm or more but not more than 1730 mm, and

a membrane thickness of 15 μm or more, but not more than 50 μm,

zero transversal production direction (TD) shrinkage,

a total thickness of 10 μm or more but not more than 50 μm,

a width of 15 mm or more but not more than 900 mm,

a length of more than 200 m but not more than 3000 m, and

an average pore size between 0,02 μm and 0,1 μm

a poly(ethylene terephthalate) film with a thickness of more than 100 μm but not more than 150 μm,

a primer of phenolic material with a thickness of more than 8 μm but not more than 15 μm,

an adhesive layer of a synthetic rubber with a thickness of more than 20 μm but not more than 30 μm,

and a transparent poly(ethylene terephthalate) liner with a thickness of more than 35 μm but not more than 40 μm

comprising a core layer of 100 % Nylon Taffeta or Nylon/Polyester blended Taffeta,

coated on both sides with polyamide,

of a total thickness not more than 135 μm,

of a total weight not more than 80 g/m2

laminated with a metal layer with a thickness of 0,05 mm (± 0,01 mm),

containing by weight 29,75 % or more but not more than 40,25 % of triethyleneglycol di (2-ethyl hexanoate) as plasticiser,

with a light transmission of 70 % or more (as determined by the ISO 9050 standard),

with an UV transmission of 1 % or less (as determined by the ISO 9050 standard),

with a total thickness of 0,43 mm (± 0,043 mm)

consisting of antistatic materials or blended thermoplastics proving special electrostatic discharge (ESD) and outgassing properties,

having non porous, abrasion resistant or impact resistant surface properties,

fitted with a specially designed retainer system that protects the photomask or wafers from surface or cosmetic damage, and

with or without a gasket seal,

a copolymer of acrylonitrile-butadiene-styrene (ABS), whether or not mixed with polycarbonate,

layers of copper, nickel and chromium,

of acrylonitrile-butadiene-styrene with or without polycarbonate,

coated with a copper, a nickel and a chrome layers,

with a total thickness of coating of 5,54 μm or more but not more than 49,6 μm

textile strings,

a wall thickness of 3,2 mm,

a metal hollow terminal pressed on both ends, and

one or more mounting brackets,

with a length of 72 mm or more but not more than 825 mm;

with a width of 18 mm or more but not more than 155 mm

one flexible rubber hose,

one plastic hose, and

metal clips,

whether or not a resonator,

an inner diameter of not less than 5 mm and an outer diameter of not more than 35 mm,

a height of 15 mm or more, but not more than 40 mm, and

a ribbed design,

of a length of 1270 mm or more, but not more than 3200 mm,

of a width of 150 mm or more, but not more than 2000 mm,

of a thickness of 0,5 mm or more, but not more than 4 mm,

not sanded, and

not planed

a width of 210 mm or more but not more than 320 mm,

a length of 297 mm or more but not more than 450 mm,

a thickness or 0,45 mm or more but not more than 0,8 mm,

with a weight of 230 g/m2 or more but not more than 280 g/m2, and

cut into rectangles with a side length of 40 cm or more but not more than 140 cm

a length of 20 metres or more but not more than 30 metres, and

a maximum width of 2,5 metres,

a poly(ethylene terephthalate) core, and

an outer layer of a copolymer of poly(ethyleneterephthalate) and poly(ethyleneisophthalate),

of a thickness of 200 μm or more but not more than 280 μm, and

of a weight of 20 g/m2 or more but not more than 50 g/m2

weighing 30 g/m2 or more, but not more than 60 g/m2,

containing fibres of polypropylene or of polypropylene and polyethylene,

whether or not printed, with:

on one side, 65 % of the total surface area having circular bobbles of 4mm in diameter, consisting of anchored, elevated un-bonded curly fibres, suitable for the engagement of extruded hook materials, and the remaining 35 % of the surface area being bonded, and

on other side a smooth untextured surface,

with a melt blown layer, laminated on each side with spunbonded filaments of polypropylene,

with a weight of not more than 150 g/m2,

in the piece or simply cut into squares or rectangles, and

not impregnated

of a weight of more than 80 g/m2 but not more than 105 g/m2, and

an air resistance (Gurley) of 8 seconds or more but not more than 75 seconds (as determined by the ISO 5636/5 method)

of weight of 160 g/m2 or more but not more than 300 g/m2,

whether or not laminated on one side with a membrane or a membrane and aluminium,

a weight of 25 g/m2 or more but not more than 150 g/m2,

in the piece or simply cut into squares or rectangles,

not impregnated,

with cross-directional or machine-directional stretch properties,

with a weight of 85 g/m2,

with a constant thickness of 95 μm (± 5 μm),

neither coated nor covered,

in 1 m wide rolls of 2000m to 5000 m length,

one layer consisting of knitted or crocheted polyester textile fabric,

other layer consisting of polyurethane foam,

a weight of 150 g/m2 or more, but not more than 500 g/m2,

a thickness of 1 mm or more, but not more than 5 mm,

of synthetic diamonds which are agglomerated with a metal alloy, ceramic alloy or plastic alloy,

having a self-sharpening effect by constant release of the diamonds,

suitable for abrasive cutting of wafers,

whether or not containing a hole in the centre,

whether or not on a support,

with a weight of not more than 377 g per piece, and

with an external diameter of not more than 206 mm

2 % or more of diboron trioxide,

28 % or less of silicon dioxide, and

60 % or more of dialuminium trioxide

a scratch proof coating of a thickness of 45 μm (+/– 5 μm),

a total thickness of 0,45 mm or more but not more than 1,1 mm,

a width of 300 mm or more but not more than 3210 mm,

a length of 300 mm or more but not more than 2000 mm,

a visible light transmission of 90 % or more,

an optical distortion of 55° or more

with a total thickness variation of 1 μm or less, and

laser-engraved

whether or not a layer of chrome,

a break-resistance adhesive tape or hot-melt adhesive, and

a release film on the front side and protective paper at the back side,

a mirror support

a plastic casing, and

an integrated circuit,

whether or not equipped with plastic backing plate,

whether or not equipped with a heating element,

whether or not equipped with Blind Spot Module (BSM) display

a length of 1516 mm (± 1 mm);

a width of 553 mm (± 1 mm);

a thickness of 3 mm (± 0,1 mm);

the back of the mirror covered with protective polyethylene (PE) film, with a thickness of 0,11 mm or more but not more than 0,13 mm;

a lead content of not more than 90 mg/kg; and

a corrosion resistance of 72 hours or more according to ISO 9227 salt spray test

9 % or more but not more than 16 % of magnesium oxide,

19 % or more but not more than 25 % of aluminium oxide,

0 % or more but not more than 2 % of boron oxide,

without calcium oxide,

10 ppm per °C or more but not more than 12 ppm per °C in the length and width, and

20 ppm per °C or more but not more than 30 ppm per °C in the thickness, with a glass transition temperature of 152 °C or more but not more than 153 °C (measured according IPC-TM-650)

a thickness of 10 cm or more but not more than 40 cm, and

a weight of 100 kg or more

78 % or more of dysprosium, and

18 % or more but not more than 22 % of iron

of martensitic stainless steel according to specification 17-4PH,

injection moulded,

with a rockwell hardness of 38 (± 1) or 53 (+ 2/– 1),

measuring 9 mm × 5,5 mm × 6,5 mm or more, but not more than 35 mm × 17 mm × 8 mm,

a thickness of 2,67 mm or more, but not more than 4,11 mm,

a width of 12,57 mm or more, but not more than 16,01 mm,

a torque of 18,05 Nm or more, but not more than 73,5 Nm,

an angle between the free position and the nominal position in exercise of 76° or more, but not more than 218°,

a diameter of 5752 mm or more but not more than 5758 mm,

a height of 3452 mm or more but not more than 3454 mm,

a total weight 167875 kg or more but not more than 168125 kg,

whether or not with parts of other material

whether or not with parts of other metals

whether or not surface treated

whether or not printed

with a chrome coating,

of a diameter of 11 mm or more, but not more than 28 mm,

of a length of 80 mm or more, but not more than 600 mm,

with at least one layer of woven glass fibre, impregnated with a fire- retardant artificial or synthetic resin with a glass transition temperature (Tg) of more than 130 °C as measured according to IPC-TM-650, method 2.4.25,

coated on one or both sides with a copper film with a thickness of not more than 3,2 mm,

poly(tetrafluoroethylene) (CAS RN 9002-84-0),

poly(oxy-(2,6-dimethyl)-1,4-phenylene) (CAS RN 25134-01-4),

epoxy resin having a thermal expansion of not more than 10 ppm in length and width and not more than 25 ppm in height,

a width of 610 mm or more but not more than 620 mm, and

a diameter of 690 mm or more but not more than 710 mm,

consisting of at least a central layer of paper or one central sheet of any type of nonwoven fibre, laminated on each side with glass-fibre fabric and impregnated with epoxide resin, or

consisting of multiple layers of paper, impregnated with phenolic resin,

consisting of at least one layer of fibreglass fabric impregnated with epoxide resin,

covered on one or both sides with copper foilwith a thickness of not more than 0,15mm, and

with a dielectric constant (DK) of less than 3,9 and a loss factor (Df) of less than 0,015 at a measuring frequency of 10GHz, as measured according to IPC-TM-650

containing 1 mg/kg or less of sodium, and

mounted on a copper or aluminium support

0,25 % or more but not more than 7 % of zinc, and

1 % or more but not more than 3 % of magnesium, and

1 % or more but not more than 5 % of copper, and

not more than 1 % of manganese,

0,10 % or more but not more than 5 % of copper, and

0,2 % or more but not more than 6 % of magnesium, and

0,10 % or more but not more than 7 % of zinc, and

not more than 1 % of manganese,

having a purity of 99,99 % by weight,

of a thickness of 0,021 mm or more but not more than 0,2 mm,

with a width of 500 mm,

with a surface oxide layer by 3 to 4 nm thick,

and with a cubic texture of more than 95 %

an aluminium content of 99,98 % or more

a thickness of 0,070 mm or more but not more than 0,125 mm

with a cubic texture

a width of 595 mm or more but not more than 605 mm, and

a diameter of 690 mm or more but not more than 710 mm,

an outer diameter of 60 mm or more but not more than 420 mm, and

a wall thickness of 10 mm or more but not more than 80 mm

height of more than 10 mm but not more than 200 mm,

width of more than 10 mm but not more than 200 mm,

length of more than 10 mm but not more than 200 mm,

internal porosity not more than 1 mm,

outer porosity not more than 2 mm,

Rockwell hardness HRB 10 or more,

consisting of eight or more layers of aluminium (CAS RN 7429-90-5) of a purity of 99,8 % or more,

with an optical density of each aluminium layer of not more than 3,0,

with each aluminium layer separated by a resin layer,

on a carrier film of PET, and

on rolls of up to 50000 metres in length

a maximum cross-sectional dimension of not more than 50 μm

a resistance of 40 Ohm or more but not more than 300 Ohm at length of 1 metre

containing by weight 99,95 % or more of tungsten, and

with a maximum cross-sectional dimension of not more than 1,02 mm

a purity by weight of 99 % or more, and

a particle size of 1,0 μm or more, but not more than 5,0 μm

a copper-chromium alloy backing plate,

a diameter of 312 mm, and

a thickness of 6,3 mm

of purity by weight of more than 99,5 %

with a particle size of 0,2 mm or more but not more than 0,8 mm

35 % (± 2 %) cobalt,

25 % (± 1 %) nickel,

19 % (± 1 %) chromium, and

7 % (± 2 %) iron,

with a height of 17,8 cm or more, a length of 180 cm or more and a width of 48,3cm or more,

a weight of 680 kg or more,

3 % or more but not more than 6 % of aluminium,

2,5 % or more but not more than 5 % of tin,

2,5 % or more but not more than 4,5 % of zirconium,

0,2 % or more but not more than 1 % of niobium,

0,1 % or more but not more than 1 % of molybdenum,

0,1 % or more but not more than 0,5 % of silicon

with a height of 17,8 cm or more, a length of 180 cm or more, a width of 48,3 cm or more,

a weight of 680 kg or more,

3 % or more but not more than 7 % of aluminium,

1 % or more but not more than 5 % of tin,

3 % or more but not more than 5 % of zirconium,

4 % or more but not more than 8 % of molybdenum

with a diameter of 63,5 cm or more and a length of 450 cm or more,

a weight of 6350 kg or more,

5,5 % or more but not more than 6,7 % of aluminium,

3,7 % of more but not more than 4,9 % of vanadium

a height of 20,3 cm or more, but not more than 23,3 cm,

a length of 246,1 cm or more, but not more than 289,6 cm,

a width of 40,6 cm or more, but not more than 46,7 cm,

a weight of 820 kg or more but not more than 965 kg,

5,2 % or more but not more than 6,2 % of aluminium,

2,5 % or more but not more than 4,8 % of vanadium

a uniform solid cross-section in the form of a cylinder,

with a diameter of 0,8 mm or more, but not more than 5 mm,

an aluminium content by weight of 0,3 % or more, but not more than 0,7 %,

a silicon content by weight of 0,3 % or more, but not more than 0,6 %,

a niobium content by weight of 0,1 or more, but not more than 0,3 %, and

an iron content by weight of not more than 0,2 %

a purity of 99,995 % by weight or more,

a diameter of 140 mm or more but not more than 200 mm,

a weight of 5 kg or more but not more than 300 kg

22 % (± 1 %) of vanadium, and

4 % (± 0,5 %) of aluminium,

15 % (± 1 %) of vanadium,

3 % (± 0,5 %) of chromium,

3 % (± 0,5 % of tin, and

3 % (± 0,5 %) of aluminium

a thickness of 0,4 mm or more, but not more than 100 mm,

a length of not more than 14 m, and

a width of not more than 4 m

of a width of more than 750 mm

of a thickness of not more than 3 mm

containing more than 0,07 % by weight of oxygen (O2),

of a thickness of 0,4 mm or more but not more than 2,5 mm,

conforming to the Vickers hardness HV1 standard of not more than 170,

a diameter of 19 mm or more but not more than 159 mm,

a wall thickness of 0,4 mm or more but not more than 8 mm, and

a maximum length of 18 m

temples,

blanks of a kind used for the manufacture of spectacle parts, and

bolts of the kind used for spectacle frames and mountings,

whether or not with parts of metal, plastic, glass fibre reinforced epoxide resin or wood,

whether or not printed or surface treated,

whether or not with electrical conducting elements,

whether or not with keypads foil glued on the keyboard,

whether or not with protective foil,

single or multilayer

an external diameter of 21 mm or more but not more than 23 mm,

a width with screw of 19 mm or more but not more than 23 mm,

a U-shaped plastic outer ring,

an assembly screw fitted to the internal diameter and used as an inner ring

with a diameter of 99,00 mm or more but not more than 136,5 mm (±1mm),

whether or not with a ring-pull aperture

self-propelled lawn mowers, with a seat of subheading 84331151, and hand-operated lawn mowers of subheading 84331190,

tractors of subheading 87019190, whose main function is that of a lawn mower,

four stroke mowers with motor of a cylinder capacity of not less than 300 cc of subheading 84332010, or

snowploughs and snow blowers of subheading 843020

6 cylinders,

an output of 75 kW or more, but not more than 80 kW,

inlet and exhaust valves modified to operate continuously in heavy duty applications,

a capacity of not more than 3850 cm3, and

a rated output of 15 kW or more but not more than 85 kW,

a heat-resistance of not more than 1050 °C, and

a hole to insert a turbine wheel, whereby the hole has a diameter of 28 mm or more, but not more than 181 mm

a camshaft position sensor (CMPS),

metal brackets for mounting on an engine, and

two or more gaskets,

a throttle,

a boost pressure sensor,

an opening pressure of 1 bar or more, but not more than 3 bar,

a closing pressure of more than 0,7 bar,

a one-way valve,

of a precision-cast nickel based alloy complying with standard DIN G- NiCr13Al6MoNb or DIN G- NiCr13Al16MoNb or DIN G- NiCo10W10Cr9AlTi or DIN G- NiCr12Al6MoNb or AMS AISI:686,

with a heat-resistance of not more than 1100 °C,

with a diameter of 28 mm or more, but not more than 180 mm,

with a height of 20 mm or more, but not more than 150 mm

a heat-resistance of not more than 1050 °C, and

a hole to insert a turbine wheel, whereby the hole has a diameter of 28 mm or more, but not more than 181 mm

whether or not with conducting horns and connecting sleeves, having an operating distance of 20 mm or more but not more than 40 mm,

with a length of not more than 350 mm,

with a diameter of not more than 75 mm,

with a height of not more than 110 mm

an operating pressure of 200 bar or more, but not more than 350 bar,

a flow control, and

a pressure relief valve,

discharging at least 400 cm3 fluid per minute,

with a noise level limited to 6 dBA,

with the inside diameter of the suction opening and discharge outlet of not more than 15 mm, and

working at ambient temperatures down to – 10 °C

consisting of aluminum alloys,

with a diameter of 38 mm or 50 mm,

with two concentric, annular grooves formed on its surface,

anodized,

driven by on-off single phase alternate current (AC) or brushless direct current (BLDC) variable speed motors

with a nominal power rating of not more than 1,5 kW

a flow of 4,5 l/min or more, but not more than 7 l/min,

power input of not more than 8,1 W, and

a gauge pressure capacity not exceeding 400 hPa (0,4 bar),

a length of 166 mm (+/– 1 mm),

a diameter of 70 mm (+/– 1 mm),

an internal capacity of 280 cm3 or more,

a water absorption rate of 17 g or more, and

an internal purity expressed by permissible amount of impurities of not more than 0,9 mg/dm2,

a length of 143 mm or more but not more than 292 mm,

a diameter of 31 mm or more but not more than 99 mm,

a spangle length of not more than 0,2 mm and a thickness of not more than 0,06 mm, and

a solid particle diameter of not more than 0,06 mm,

ultrafiltration system

carbon filtration system

water softener system

a single-phase AC motor,

an epicyclic gearing,

a cutter blade,

a capacitor,

a part fitted with a threaded bolt,

a voltage of 14,4 V or more but not more than 42 V,

an amperage of 10 A or more but not more than 42 A,

electrically heated,

with opening,

with a multiplicity of tips (holes) of platinum/rhodium alloy,

used to melt glass batches and condition molten glass,

for drawing into continuous fibres

8 oil chambers,

a phasing range of at least 38°, but not more than 62°,

a steel and/or steel alloy sprocket,

a steel and/or steel alloy rotor

having interior surfaces of austenitic stainless steel, and

with a process capacity up to 15000 litres,

whether or not combined with a clean-in-process system and/or a dedicated paired media hold vessel

with a 16000 tonne pressure rating,

with a 1100 mm diameter Bolster (± 1mm),

with a 1400 mm main cylinder (± 1mm),

with a Fixed and floating link frame, multiple pump high pressure hydraulic accumulator and pressure system,

with a double arm manipulator arrangement and connections for piping and electrical systems,

with a total weight 310 tonnes (± 10 tonnes), and

creating 30000 atmospheres at 1500 degrees centigrade using Low Frequency Alternating Current (16000 amps)

with a plunger,

with at least 275 MPa internal tightness,

with a plastic connector with 2 silver or tin pins

a length of not more than 18 mm (± 1 mm),

a width of not more than 30 mm (± 1 mm),

an opening pressure of not more than 800 kPa,

an external diameter not more than 37 mm

at least 5 but not more than 9 outlet holes with at least 0,110 mm but not more than 0,134 mm diameter,

at least 640 cm3 / minute but not more than 805 cm3 / minute flow rate,

at least 19 but not more than 300 MPa operating pressure

made of steel,

with an outlet hole with a diameter of at least 0,175 mm, but not more than 0,185 mm,

with an inlet hole with a diameter of at least 0,255 mm, but not more than 0,265 mm,

with chromium nitride coating,

with a surface roughness of Rp 0,4

a plunger,

DLC (Diamond-like carbon) coating,

a solenoid with a of coil resistance of at least 2,6 Ohm, but not more than 3 Ohm,

a supply voltage of 12 V

with a solenoid with a coil resistance of at least 0,19 Ohm, but not more than 0,52 Omh, and with an inductance of at least 0,083 mH, but not more than 0,172 mH,

with a supply voltage of 24 V,

operating at a DC of at least 15,5 A, but not more than 16,5 A

a solenoid pilot valve

a brass valve body including valve slider and copper connections

made of steel and/or steel alloy(s),

without integrated circuit,

of not more than 1000 kPa operating pressure,

with a flow quantity of not more than 5 l/min,

without an electromagnet

for the opening and closing of the flow of fuel,

consisting of a shaft and a blade,

with 8 holes on the blade,

made of metal and/or metal alloy(s)

with an outside diameter of 28 mm or more but not more than 140 mm,

with an operational thermal stress of more than 150 °C at a working pressure of not more than 14 MPa,

with an internal diameter of 3 mm or more,

with an external diameter of not more than 100 mm,

with a width of not more than 40 mm,

whether or not equipped with a duster,

of precision-cast grey cast iron complying with standard DIN EN 1561 or precision-cast ductile cast iron complying with DIN EN 1560,

with oil chambers,

without bearings,

with a diameter of 50 mm or more, but not more than 250 mm,

with a height of 40 mm or more, but not more than 150 mm,

whether or not with water chambers and connectors

a rated torque of 50 Nm or more but not more than 9000 Nm,

standard ratios of 1:50 or more but not more than 1:475,

lost motion of not more than one arc minute,

an efficiency of more than 80 %,

a rated torque of 25 Nm or more, but not more than 70 Nm,

standard gear ratios of 1:12,7 or more, but not more than 1:64,3

measurements (without shafts) of not more than 154 mm × 115 mm × 108 mm,

a weight of not more than 3,3 kg,

a maximum rotation speed of the input shaft of 2700 rpm or more, but not more than 3200 rpm,

a torque of the output shaft of not more than 10,4 Nm,

a rotation speed of the output shaft of not more than 930 rpm at 2800 rpm input speed, and

an operating temperature range of – 5 °C or more, but not more than + 40 °C,

a reduction of 20,63:1 or more, but not more than 22,68:1,

an input speed of 1800 rpm or more when loaded and of not more than 3000 rpm when unloaded,

a continuous output torque of 142 Nm or more, but not more than 156 Nm,

an intermittent output torque of 264 Nm or more, but not more than 291 Nm, and

an axle shaft diameter of 19,02 mm or more, but not more than 19,06 mm,

whether or not equipped with a fan impeller or with a pulley with integrated fan impeller,

not more than 3 gears,

an automatic deceleration system, and

a power reversal system,

a length without axle of 24 mm (+/– 0,3),

a diameter of 49,3 mm (+/– 0,3),

a rated voltage of 220 V AC or more but not more than 240 V AC,

a rated frequency of 50 Hz or more but not more than 60 Hz,

an input power of not more than 4 W,

a rotation speed of 4 rpm or more but not more than 4,8 rpm,

an output torque of not less than 10 kgf/cm

with a speed rotation of not more than 7000 rpm (without load),

with a nominal voltage of 12 V (± 4 V),

with a maximum power of 13,78 W ( at 3,09 A),

with a specified temperature range from – 40 °C to 160 °C,

with a gear connection,

with a mechanical attachment interface,

with 2 electrical connections,

with a maximum torque of 100 Nm

with a rotor speed of not more than 6500 rpm when not loaded;

with a rated voltage of 12,0 V (+/– 0,1);

of a specified temperature range of – 40 °C or more, but not more than + 165 °C;

with or without a connecting pinion;

with or without an engine connector

with a speed rotation of not more than 6500 rpm (without load),

with a nominal voltage of 12 V (± 4 V),

with a maximal power below than 20 W,

with a specified temperature range from – 40 °C to 160 °C,

with a worm gear drive,

with a mechanical attachment interface,

with 2 electrical connections,

with a maximum torque of 75 Nm

with a rotor speed of 3500 rpm or more but not more than 5000 rpm loaded and not more than 6500 rpm when not loaded

with a power supply voltage of 100 V or more but not more than 240 V

a DC motor,

an integrated gear mechanism,

a (pulling) force of 200 N or more at a minimum of 140 °C elevated ambient temperature,

a (pulling) force of 250 N or more in each position of its stroke,

an effective stroke of 15 mm or more but not more than 25 mm,

with or without an on-board diagnostics interface

an angle of step of 7,5° (± 0,5°),

a two-phase winding,

a rated voltage of 9 V or more, but not more than 16,0 V,

of a specified temperature range covering at least – 40 °C to + 105 °C,

with or without connecting pinion,

with or without motor drive connector

a multiple-phase winding,

an external diameter of 28 mm or more but not more than 35 mm,

a rated speed of not more than 12000 rpm,

a power supply voltage of 8 V or more but not more than 27 V

an angle of step of 7,5° (± 0,5°),

a pull-out torque at 25 °C of 25 mNm or more,

a pull-out pulse rate of 1500 pps or more,

a two-phase winding, and

a rated voltage of 10,5 V or more, but not more than 16,0 V

a rated output of 1,2 kW,

a supply voltage of 230 V, and

engine brake,

assembled to a reduction gear with output shaft, which is contained in a plastic housing,

a multiple-phase winding,

an external diameter of 30 mm or more but not more than 80 mm,

a rated speed of not more than 15000 rpm,

an output of 45 W or more but not more than 300 W, and

a supply voltage of 9 V or more but not more than 50 V,

whether or not with a drive disc,

whether or not with a crankcase,

whether or not with a fan,

whether or not with a cap assembly,

whether or not with a sun gear,

whether or not with a speed and rotational direction encoder,

whether or not with or without a speed or rotational direction sensor of resolver type or Hall effect type

an external diameter of 90 mm or more, but not more than 110 mm,

a rated speed of not more than 3680 rpm,

an output of 600 W or more but not more than 740 W at 2300 rpm and at 80 °C,

a supply voltage of 12 V,

a torque of not more than 5,67 Nm,

a rotor position sensor,

an electronic star-point relay, and

for use with an electric power steering control module

an external diameter of 80 mm or more, but not more than 200 mm,

a supply voltage of 9 V or more, but not more than 16 V,

an output at 20 °C of 300 W or more, but not more than 750 W,

a torque at 20 °C of 2,00 Nm or more, but not more than 7,00 Nm,

a rated speed at 20 °C of 600 rpm or more, but not more than 3100 rpm,

with or without the rotor angle position sensor of resolver type or Hall effect type,

an external diameter of 27,5 mm or more, but not more than 45 mm,

a rated speed of 11000 rpm or more, but not more than 23200 rpm,

a rated supply voltage of 3,6 V or more, but not more than 230 V,

an output power of not more than 529 W,

a free load current of not more than 3,1 A,

a maximum efficiency of 54 % or more,

a specified speed of not more than 4100 rpm,

a minimum output of 400 W, but not more than 1,3 kW (at 12 V),

a flange diameter of 90 mm or more, but not more than 150 mm,

a maximum length of 210 mm, measured from the beginning of the shaft to the outer ending,

a housing length of not more than 160 mm, measured from the flange to the outer ending,

a maximum of two-piece (basic housing including electric components and flange with minimum 2 and maximum 11 bore holes) aluminium diecast or sheet steel housing whether or not with a sealing compound (groove with an O-ring and grease),

a stator with single T-tooth design and single coil windings in 9/6 or 12/8 topology, and

surface magnets

electronic control operating by Hall Effect position sensors,

voltage input 9 V or more but not more than 16 V,

external diameter of the motor 70 mm or more but not more than 80 mm,

output motor power 350 W or more but not more than 550 W,

maximum output torque 50 Nm or more but not more than 52 Nm,

maximum output rotation speed 280 rpm or more but not more than 300 rpm,

coaxial male spline outputs of outer diameter 20 mm (± 1 mm), 17 teeth and minimum length of teeth 25 mm (± 1 mm), and

with distance between root of splines 119 mm (± 1 mm),

a torque output of 200 Nm or more but not more than 300 Nm

a power output of 50 kW or more but not more than 100 kW

a rated speed of not more than 12500 rpm

an AC or DC motor whether or not with transmission,

power electronics

an output of 340 W or more but not more than 7,4 kW,

a flange of dimensions of not more than 180 mm × 180 mm, and

a length from flange to extreme end of resolver of not more than 271 mm

a Hydrogen generator (desulphurizer, reformer and cleaner)

a PEM fuel cell stack, and

an Inverter,

consisting of at least phosphoric acid fuel cells,

in a housing with integrated water management and gas treatment,

for permanent, stationary energy supply

diameter of the rotor body of 17 mm or more but not more than 37 mm,

length of the rotor body of 12 mm or more but not more than 36 mm,

shaft length of 52 mm or more but not more than 82 mm

a capacity of 192 Watts or 216 Watts,

dimensions of not more than 27,1 × 26,6 × 18 mm,

an operating temperature range of – 40 °C or more, but not more than + 125 °C,

three or four inductively coupled copper wire windings, and

9 connection pins at the bottom

a capacity of 432 Watts,

dimensions of not more than 24 mm × 21 mm × 19 mm,

an operating temperature range of – 20 °C or more, but not more than + 85 °C,

two windings, and

5 connection pins at the bottom

a capacity of 433 Watts,

dimensions of not more than 37,3 × 38,2 × 28,5 mm,

an operating temperature range of – 40 °C or more, but not more than + 125 °C,

four inductively coupled copper wire windings, and

13 connection pins at the bottom

with a capacity of 1 kVA or less,

without plugs or cables,

a capacity of 0,2 Watts,

dimensions of not more than 15 × 15,5 × 14 mm,

an operating temperature range of – 10 °C or more, but not more than + 125 °C,

two inductively coupled copper wire windings,

5 connection pins at the bottom, and

a copper shielding

with two output connectors,

with two input connectors which are available and useable in parallel,

able to switch between bright and dimmed operation mode,

with an input voltage of 40 V (+ 25 % – 15 %) or 42 V (+ 25 % – 15 %) in bright operation mode, with an input voltage of 30 V (± 4 V) in dimmed operation mode, or

with an input voltage of 230 V (+ 20 % – 15 %) in bright operation mode, with an input voltage of 160 V (± 15 %) in dimmed operation mode, or

with an input voltage of 120 V (15 % – 35 %) in bright operation mode, with an input voltage of 60 V (± 20 %) in dimmed operation mode,

with an input current reaching 80 % of its nominal value within 20 ms,

with an input frequency of 45 Hz or more, but not more than 65 Hz for 42 V and 230 V, and 45-70 Hz for 120 V versions,

with an maximum inrush current overshoot of not more than 250 % of the input current,

with a period of the inrush current overshoot of not more than 100 ms,

with an input current undershoot of not less than 50 % of the input current,

with a period of the inrush current undershoot of not more than 20 ms,

with a presettable output current,

with an output current reaching 90 % of its nominal pre-set value within 50 ms,

with an output current reaching zero within 30 ms after removal of the input voltage,

with an defined failure status in case of no-load or too-high load (end-of-life function)

with an input AC voltage of 100-240 V at frequency of 50-60 Hz,

with two output DC voltages of 9 V or more but not more than 12 V and 396 V or more but not more than 420 V,

output cables without connectors, and

in a plastic enclosure with dimensions 110 mm (± 0,5 mm) × 60 mm (± 0,5 mm) × 38 mm (± 1 mm),

without housing, or

with housing with connection pins, connection studs, screw connectors, unprotected line connections, connection elements which allow the mounting to a printed circuit board by soldering or any other technology, or other wiring connections requiring further processing

power transistors,

integrated circuits,

whether or not containing diodes and with or without thermistors,

an operating voltage of not more than 600 V,

not more than three electrical outputs each containing two power switches (whether MOSFET (Metal Oxide Semiconductor Field-Effect Transistor) or IGBT (Insulated Gate Bi-polar Transistors)) and internal drives, and

a rms (root mean square) current rating of not more than 15,7 A

one or six 3-phase motor outputs with maximum 3 × 32 A,

a main power input of 220 V AC or more, but not more than 480 V AC, or 280 V DC or more, but not more than 800 V DC,

a logic power input of 24 V DC,

an EtherCat communication interface, and

a dimension of 150 × 140 × 120 mm or more, but not more than 335 × 430 × 179 mm

a rated power of not more than 100 W,

an input voltage of 80 V or more, but not more than 305 V,

an certified input frequency of 47 Hz or more, but not more than 440 Hz,

one or more constant voltage output(s),

an operating temperature range of – 40 °C or more, but not more than + 85 °C,

pins for mounting to a printed circuit

a DC to DC converter

a charger of a capacity of not not more than 7 kW

switching functions

an inductance of 4,7 μH (± 20 %),

a DC resistance of not more than 0,1 Ohms,

an insulation resistance of 100 MOhms or more at 500 V (DC),

a power consumption of not more than 6 W,

an insulation resistance of more than 100 M ohms, and

an insert hole of 11,4 mm or more, but not more than 11,8 mm

a rated power of more than 10 W but not more than 15 W,

an insulation resistance of 100 M Ohms or more,

a DC resistance of not more than 34,8 Ohm (± 10 %) at 20 °C,

a rated current of not more than 1,22 A,

a rated voltage of not more than 25 V

with one or more windings, with an inductivity per winding of no more than 62 mH, attached to one or more carrier materials,

with ferrites,

with one or more Negative Temperature Coefficient resistors as a temperature sensor,

whether or not with insulation covers, spacers and connection cables

being a power electronic circuit mounted on the PCB, equipped with SGCT thyristor and electric and electronic components,

having an ability to block the voltage - 6500 V - in both directions (conducting and the reverse direction),

a length of 9 mm or more but not more than 105 mm,

a width of 5 mm or more but not more than 105 mm, and

a height of 2 mm or more but not more than 55 mm

a length of 15 mm or more but not more than 52 mm,

a width of 5 mm or more but not more than 42 mm,

a length of 97,5 mm or more, but not more than 225 mm

a diameter of 19 mm or more, but not more than 25 mm

a length of 30,4 mm (± 0,05 mm),

a width of 12,5 mm (± 0,15 mm),

a thickness of 6,9 mm (± 0,05 mm), or composed of ferrites in the shape of a quarter sleeves with:

a length of 46 mm (± 0,75 mm),

a width of 29,7 mm (± 0,2 mm),

an external diameter of not more than 45 mm,

a height of not more than 45 mm,

a length of not more than 140 mm,

a width of not more than 90 mm, and

a thickness of not more than 55 mm,

a length of not more than 75 mm,

a width of not more than 40 mm,

a thickness of not more than 7 mm, and

a radius of curvature of more than 86 mm but not more than 241 mm,

whether or not containing a hole in the centre,

with a diameter of not more than 90 mm,

consisting of at least neodymium, iron and boron,

with a width of 9,1 mm or more but not more than 10,5 mm,

with a length of 20 mm or more but not more than 30,1 mm,

whether or not with bevelled edges,

of a length of 27 mm or more but not more than 32 mm (± 0,15 mm),

of a width of 8,5 mm or more but not more than 9,5 mm (+ 0,05 mm /– 0,09 mm),

of a thickness of 5,5 mm or more but not more than 5,8 mm (+ 0/– 0,2 mm), and

of a weight of 6,1 g or more but not more than 8,3 g

of a length of 30 mm or more but not more than 50 mm (± 1 mm),

of a width of 33 mm or more but not more than 55 mm (± 1 mm),

of a height of 12,5 mm or more but not more than 21,5 mm (± 1 mm),

of a thickness of 3,85 mm or more but not more than 6,8 mm (± 0,15 mm) and having an outer radius of 19 mm or more but not more than 29,4 mm (± 0,2 mm)

a plunger,

a diameter of 12,9 mm (+/– 0,1),

a height without plunger of 20,5 mm (+/– 0,1),

an electric cable with connector, and

a diameter of 14,0 mm or more but not more than 26,0 mm,

a length of 2,2 mm or more but not more than 51 mm,

a voltage of 1,5 V or more, but not more than 3,6 V,

a capacity of 0,15 Ah or more, but not more than 5,00 Ah,

a diameter of 20 mm or more but not more than 25 mm

a length of 3 mm or more but not more than 6 mm

a voltage of 3 V or more but not more than 3,4 V

a capacity of 200 mAh or more but not more than 600 mAh

an automotive test temperature range from – 40 °C to + 125 °C

a charge acceptance capacity of 200 % or more of the level of an equivalent conventional flooded battery during the first 5 seconds of charge,

a liquid electrolyte,

a voltage of 190 V or more but not more than 210 V,

a length of 220 mm or more but not more than 280 mm,

a width of 500 mm or more but not more than 600 mm,

a height of 100 mm or more but not more than 150 mm,

a nominal capacity of 8,8 Ah or more, but not more than 18 Ah,

a nominal voltage of 36 V or more, but not more than 48 V,

a power of 300 Wh or more, but not more than 648 Wh,

a rated voltage of 12 V,

a length of 350 mm or more but not more than 355 mm,

a width of 170 mm or more but not more than 180 mm,

a height of 180 mm or more but not more than 195 mm,

weighing 10 kg or more but not more than 15 kg,

a nominal charge of 60 Ah or more, but not more than 80 Ah

a nominal capacity of 72 Ah or more, but not more than 100 Ah,

a nominal voltage of 3,2 V,

a weight of 1,9 kg more, but not more than 3,4 kg,

a width of 352,5 mm (± 1 mm) or 367,1 mm (± 1 mm),

a depth of 300 mm (± 2 mm) or 272,6 mm (± 1 mm),

a height of 268,9 mm (± 1,4 mm) or 229,5 mm (± 1 mm),

a weight of 45,9 kg or 46,3 kg,

a rating of 75 Ah, and

a nominal voltage of 60 V

a nominal capacity of 10 Ah or more, but not more than 20 Ah,

a nominal voltage of 12,8 V (± 0,05) or more, but not more than 15,2 V (± 0,05),

a power of 128 Wh or more, but not more than 256 Wh,

a length of 150 mm or more, but not more than 300 mm

a width of 700 mm or more, but not more than 1000 mm

a height of 1100 mm or more, but not more than 1500 mm

a weight of 75 kg or more, but not more than 160 kg

a nominal capacity not less than 150 Ah and not more than 500 Ah

a length of 1200 mm or more, but not more than 2000 mm

a width of 800 mm or more, but not more than 1300 mm

a height of 2000 mm or more, but not more than 2800 mm

a weight of 1800 kg or more, but not more than 3000 kg

a nominal capacity of 2800 Ah or more but not more than 7200 Ah

a thickness of not more than 4,15 mm,

a width of not more than 245,15 mm,

a length of not more than 90,15 mm,

a nominal capacity of 1000 mAh or more but not more than 10000 mAh,

a weight of not more than 250 g,

a nominal capacity of 1060 mAh,

a nominal voltage of 7,4 V (average voltage at 0,2 C discharge),

a charging voltage of 8,4 V (± 0,05),

a length of 86,4 mm (± 0,1),

a width of 45 mm (± 0,1),

a height of 11 mm (± 0,1),

a thickness of not more than 6 mm,

a width of not more than 100 mm,

a length of not more than 150,15 mm,

a nominal capacity of 1000 mAh or more but not more than 10000 mAh,

a weight of not more than 150 g,

a length of 298 mm or more, but not more than 408 mm,

a width of 33,5 mm or more, but not more than 209 mm,

a height of 138 mm or more, but not more than 228 mm,

a weight of 3,6 kg or more, but not more than 17 kg, and

a power of 458 Wh or more, but not more than 2158 Wh

a length of 1203 mm or more, but not more than 1297 mm,

a width of 282 mm or more, but not more than 772 mm,

a height of 792 mm or more, but not more than 839 mm,

a weight of 253 kg or more, but not more than 293 kg,

power of 22 kWh or 26 kWh, and

constituted of 24 or 48 modules

a length of 1213 mm or more, but not more than 1575 mm,

a width of 245 mm or more but not more than 1200 mm,

a height of 265 mm or more, but not more than 755 mm,

a weight of 265 kg or more but not more than 294 kg,

a nominal capacity of 66,6 Ah,

3,5 VDC to 3,8 VDC,

300 mAh to 900 mAh, and

a diameter of 10,0 mm to 14,5 mm

a length of 700 mm or more, but not more than 2820 mm

a width of 935 mm or more, but not more than 1660 mm

a height of 85 mm or more, but not more than 700 mm

a weight of 250 kgor more, but not more than 700 kg

a power of not more than 175 kWh

a metal casing,

a length of 173 mm (± 0,15 mm),

a width of 21 mm (± 0,1 mm),

a height of 91 mm (± 0,15 mm),

a nominal voltage of 3,3 V, and

a nominal capacity of 21 Ah or more

a metal casing,

a length of 171 mm (± 3 mm),

a width of 45,5 mm (± 1 mm),

a height of 115 mm (± 1 mm),

a nominal voltage of 3,75 V, and

a nominal capacity of 50 Ah,

of a length of 300 mm or more, but not more than 350 mm,

of a width of 79,8 mm or more, but not more than 225 mm,

of a height of 35 mm or more, but not more than 168 mm,

of a weight of 3,95 kg or more, but not more than 8,85 kg,

with a rating of 66,6 Ah or more, but not more than 129 Ah

a width of 70 mm (± 5 mm),

a thickness of 0,4 mm (± 0,2 mm),

a length of not more than 55 mm,

are connected by wire or radio frequency to each other and the motor controller card, and

regulate the functioning (switching on or off and suction capacity) of vacuum cleaners according to a stored program,

whether or not fitted with indicators that display the functioning of the vacuum cleaner (suction capacity and/or dust bag full and/or filter full)

an igniter,

a coil on plug assembly with an integrated mounting bracket,

a housing,

a length of 90 mm or more but not more than 200 mm (± 5 mm),

an operating temperature of – 40 °C or more but not more than 130 °C,

a voltage of 10,5 V or more, but not more than 16 V

with a length of 50 mm or more, but not more than 200 mm,

with an operating temperature of – 40 °C or more, but not more than 140 °C, and

with a voltage of 9 V or more, but not more than 16 V,

with or without connection cable,

an operating temperature of more than 800 °C,

a voltage of 5 V or more, but not more than 16 V,

a heating rod containing silicon nitride (Si3N4) and molybdenum disilicide (MoSi2), and

a metal housing,

two LEDs,

glass or plastic lenses, focusing/scattering the light emitted by the LEDs,

reflectors redirecting the light emitted by the LEDs,

a plastic holder with three or more brackets,

one or more 12 V bulbs,

a connector,

a plastic cover,

whether or not with a connection cable,

coil,

magnet,

metal membrane,

connector,

holder,

a printed circuit board,

a connector,

whether or not a metal holder,

with an operating temperature of – 45 °C or more, but not more than + 95 °C,

with a voltage of 9 V or more but not more than 16 V,

in a plastic housing,

whether or not with a metal holder,

with two electrical contacts,

with an adhesive layer on both sides (on the side of the plastic holder of the mirror and on the side of the mirror glass),

with a protective paper film on both sides

a transformer with an input of not more than 240 V and an output of not more than 3000 W

an AC or DC fan motor with an output of not more than 42 watts

a housing made of stainless steel

with or without a magnetron of a microwave output power of not more than 900 W

fitted with a motor having a power rating of 8 W at 4600 rpm,

governed by an electronic circuit,

operating at ambient temperatures above 110 °C,

fitted with a thermoregulator

containing side and central openings,

of annealed aluminium,

with a ceramic coating, heat resistant to more than 200 °C,

an impedance of 3 Ohm or more, but not more than 16 Ohm,

a nominal power of 2 W or more, but not more than 20 W,

with or without plastic bracket, and

with or without electric cable fitted with connectors,

of an impedance of 1,5 Ohm or more, but not more than 10 Ohm,

of a diameter of 25 mm or more but not more than 80 mm,

with frequency range of 150 Hz to 20 kHz,

with rated power of 5 W or more, but not more than 40 W, and

whether or not with electric cable with connector,

whether or not with a bracket,

an output power of 50 W,

an operating voltage of more than 9 V but not more than 16 V,

an electrical impedance of not more than 4 Ohm,

a sensitivity of more than 80 dB,

in a metal housing,

a steel coreplate, in the form of a disk on one side provided with a cylinder

a neodymium magnet

an upper plate

a lower plate

of steel,

perforated, and

measuring 60,30 mm (+ 0,00 mm /– 0,40 mm) × 15,5 mm (+ 0,00 mm /– 0,40 mm) × 4,40 mm (± 0,05 mm),

an outside diameter of 25 mm or more but not more than 250 mm,

a resonance frequency of 20 Hz or more but not more than 150 Hz,

a total height of 5 mm or more but not more than 50 mm,

an edge thickness of 0,1 mm or more but not more than 3 mm

a speaker frame and magnet system holder with a protective coating, and

an embossed anti-dust cloth

without a hard disk drive,

with or without a DVD-RW drive,

with either motion detection or capability of motion detection through IP connectivity via LAN connector

with or without a USB serial port,

a radio tuner (capable of receiving and decoding radio signals and transmitting those signals within the assembly) without signal processing capabilities,

a microprocessor capable of receiving remote control messages and controlling the tuner chipset,

a radio tuner, capable of receiving and decoding radio signals and transmitting those signals within the assembly, with a signal decoder,

a radio frequency (RF) remote control receiver,

an infrared remote control signal transmitter,

a SCART signal generator,

a TV state sensor,

an optical pick up unit with laser diodes operating at three different wavelengths,

a spindle motor,

a stepping motor

of a weight of not more than 5,9 kg,

without a housing,

of dimensions of not more than 405 mm × 315 mm,

with a single Charge-Couple-Device (CCD) or Complementary Metal Oxide Semiconductor (CMOS) sensor,

with effective pixels of not more than 5 megapixels,

a Dynamic- or Static overlay lines system,

an output NTSC video signal,

a voltage of 6,5 V or more,

an illuminance of 0,5 lux or more

an image sensor,

an objective (lens),

a colour processor,

a flexible printed circuit board or a printed circuit board,

whether or not capable of receiving audio signals,

a module dimension of not more than 15 mm × 15 mm × 15 mm,

a resolution of 2 mega pixel or more (1616*1232 pixels and higher),

whether or not wired, and

a housing,

a sensitivity in the wavelength area of 7,5 μm or more, but not more than 17 μm,

a resolution of up to 640 × 512 pixels,

a weight of not more than 400 g,

measurements of not more than 70 mm × 86 mm × 82 mm,

whether or not in a housing,

with automotive- qualified plug, and

a deviation of the output signal over the entire work temperature range of not more than 20 %

an audio frequency amplifier unit, comprising at least an audio frequency amplifier and a sound generator,

a transformer, and

a radio broadcast receiver,

without a housing, with back cover and mounting frame, or

with a housing,

excluding those combined with other apparatus,

comprising touch screen facilities, a printed circuit board with drive circuitry and power supply,

with an applicable frequency range of 10 kHz or more but no more than 100 MHz

with a housing of ceramic plates provided with electrodes

a printed circuit

processors for multi-media applications and video signal processing

FPGA (Field Programmable Gate Array)

Flash memory

operating memory

HDMI, VGA, USB and RJ-45 interfaces

sockets and plugs for connecting a LCD-monitor, a LED lighting and a control panel

the generation of driving signals for pixel addressing, or

driving addressing pixels

solely consisting of one or more TFT glass or plastic cells,

not combined with touch screen facilities,

with one or more printed circuits boards with control electronics for pixel addressing only,

with or without backlight unit, and

with or without inverters

one or more TFT glass or plastic cells,

a die cast heat sink,

a backlight unit,

one printed circuit board with micro controller, and

LVDS (Low Voltage Differential Signalling) interface,

solely consisting of one or more TFT cells,

with a diagonal measurement of the screen of 10,7 cm or more but not more than 36 cm,

with or without LED backlight,

with control electronics for pixel addressing only,

without an EPROM memory (Erasable Programmable Read-only Memory),

with digital RGB Interface (Red, Green, Blue Interface), Touch-Screen Interface,

silicon and magnesium,

with a length of 300 mm or more but not more than 2200 mm,

AC socket (for power cord connection) of 230 V,

integrated noise filter composed of capacitors and inductors,

cable connector for connecting an AC socket with the PDP (Plasma display panel) power supply unit,

a diagonal measurement of the screen of 121 cm or more, but not more than 224 cm,

with a thickness of not more than 55mm,

containing organic material,

with control electronic for pixel addressing only,

with V-by-One Interface and with or without a plug for power supply,

with or without back cover,

one or more TFT glass or plastic cells, containing organic material,

with or without combined touch screen facilities, and

one or more printed circuit boards with control electronics for pixel addressing,

with a diagonal measurement of the screen of 14,5 cm or more but not more than 38,5 cm,

with or without a touch screen,

with an LED backlight,

with a printed circuit board with EEPROM, microcontroller, LVDS receiver and other active and passive components,

with a plug for power supply and CAN and LVDS interfaces,

with or without electronic components for dynamic adjustments of colour,

in a housing, with or without mechanical, touch-sensitive or contactless control functions and with or without active cooling system,

the organic layer with organic LEDs,

two conductive layers on electron transfer and electron holes,

layers of transistors (TFT) with resolution of 1920 × 1080,

anode and cathode for power supply of organic diodes,

RGB filter,

glass or plastic protective layer,

without the electronics for pixel addressing,

with a diagonal measurement of the screen of 14,48 cm or more but not more than 31,24 cm,

with or without a touch screen,

with backlight, micro-controller,

with a CAN (Controller area network)-controller with one or more LVDS (Low-voltage differential signalling) interfaces and one or more CAN/power supply sockets or with an APIX (Automotive Pixel Link) controller with APIX interface,

in a housing with or without a heat sink at the back of the housing,

without a signal-processing module,

whether or not with haptic and acoustical feedback,

of an aluminium alloy containing silicon and magnesium,

with a length of 500 mm or more but not more than 2200 mm,

with a width of 300 mm or more but not more than 1500 mm,

with a diagonal screen measurement of 14,48 cm or more but not more than 26 cm,

without touch screen,

with a backlight and micro-controller,

with a CAN (Controller Area Network) controller, an LVDS (Low-Voltage Differential Signalling) interface and a CAN/power connector,

without a signal processing module,

with control electronics for pixel addressing only,

with a motorised mechanism for moving the display screen,

consisting of an IGBT transistor chip and a diode chip on one or more lead frames,

for a voltage of 600 V or 1200 V

an electromechanical switching function,

a load current of 3 amperes or more but not exceeding 16 amperes,

a coil voltage of 5 volts or more but not exceeding 24 volts,

a distance between the connector pins of the load circuit not more than 12,5 mm

a nominal voltage of 12 V DC

an allowable voltage of not more than 16 V DC

a coil resistance at 20 °C of 26, 7 Ohm (± 10 %)

a pick-up voltage at 60 °C of not more than 8,5 V

a drop-out voltage at 20 °C of 1 V or more

a nominal operating power at 20 °C of 5,4 Watts

a switching voltage of not more than 400 V DC

a permanent current-carrying capacity of not more than 120 A

printed circuit board,

LED diode,

connector,

brackets for mounting,

a voltage of 240 V or more but not more than 250 V,

an amperage of 4 A or more but not more than 6 A,

a voltage of 240 V or more but not more than 300 V,

an amperage of 3 A or more but not more than 15 A,

a pulse transformer, including a wide-band ferrite core,

a common mode coil,

a resistor,

a capacitor,

of copper

plated with silver nickel alloy AgNi10 or with silver containing by weight 11,2 % (± 1,0 %) of tin oxide and of indium oxide taken together

with a thickness of the plating of 0,3 mm (– 0/+ 0,015 mm)

whether or not gilded

sockets with or without fuses,

connecting ports,

a printed circuit board with embedded microprocessor, micro switch and relay,

an AC power input of 208 V or more but not more than 400 V,

a logic power input of 24 V DC,

an automatic circuit breaker,

a main power switch,

internal or external electrical connectors and cables,

in a housing with dimension of 281 mm × 180 mm × 75 mm or more, but not more than 630 mm × 420 mm × 230 mm,

with a programmable memory,

with a voltage of 8 V or more but not more than 16 V,

with at least one composite connector,

in a metal housing,

whether or not with metal holders,

a printed circuit with active and passive components,

an aluminium housing, and

multiple connectors

one or more integrated circuits, not interconnected, on separate lead frames,

also with discrete Metal Oxide Field Effect Transistors (MOSFET) for controlling DC motors in cars,

mounted in a plastic housing

2 rotary knobs

27 or more pushbuttons

LED lights

2 integrated circuits for receiving and sending of control signals via the LIN-bus

a length of 50 mm or more, but not more than 120 mm,

a width of 20 mm or more but not more than 40 mm,

a height of 30 mm or more, but not more than 120 mm,

plastic box with printed circuit board and metal holder,

with voltage of 9 V or more, but not more than 16 V,

able to control, evaluate and manage functions of assisting services in an automobile, at least wiper timing, window heating, interior lighting, seat belt reminder,

a microprocessor,

light-emitting diode (LED) or liquid crystal display (LCD) indicators,

electronic components mounted on a printed circuit,

with one or more single or multi-positional electrical switches (push-button, rotary or other),

whether or not equipped with printed circuit boards and electrical cables,

for a voltage of 9 V or more but not more than 16 V,

an antenna,

a connector,

a metal holder,

an antenna module in a plastic housing,

a connection cable with a plug,

at least two mounting brackets,

whether or not PCB including integrated circuits, diodes and transistors,

a graphite carbon shield mounted in a mini-Vogel type system

separate pyrolytic carbon blocks used as heating elements and

a cathode temperature of less than 1800 K at a filament current of 1,26 A

two outer layers of polyester,

a middle layer of acrylic polymer and silicone, and

two electric connection terminals

a mains power/ CAN (Controller area network) output socket,

a universal serial bus (USB) and audio IN/OUT ports, and

incorporating a video switching device for the interface of smart phone operating systems with the Media Orientated Systems Transport network (MOST),

a voltage of not more than 60 V,

a current of not more than 1 A,

a heat resistance of not more than 105 °C,

individual wires of a thickness of not more than 0,1 mm (± 0,01 mm) and a width of not more than 0,8 mm (± 0,03 mm),

a distance between conductors of not more than 0,5 mm, and

a pitch (distance from centreline to centreline of conductors) of not more than 1,25 mm

a coaxial cable,

two or more connectors, and

3 or more plastic clips for attachment to the dashboard,

a travel speed of not more than 24 km/h

a motor speed of not more than 4500 rpm

hydraulic pressure of not more than 25 MPa

mass of not more than 50 metric tonnes

with an operation voltage of 12V,

wrapped in tape or covered in plastic convoluted tubing,

with 16 or more strands, with all terminals to be tin plated or equipped with connectors,

of a voltage of 5 V or more but not more than 90 V,

capable of transmitting information,

a rubber grommet,

a metal attachment bracket,

a voltage of 1,25 V (± 0,25 V),

connectors fitted at one or both ends, at least one of which contains pins with a pitch of 1 mm,

outer screening shielding,

a length of not more than 2100 mm,

an operating voltage of 5 V or more, but not more than 35 V,

a temperature resistance of not more than 80 °C,

either an over-moulded 7 pin round 270° DIN male connector, a 6 pin A1101 male connector or a 8 pin A1001 male connector on one end, and

at least two stripped and tinned wires on the other end,

whether or not with mounted rubber pad with integrated strain relief

a length of not more than 1800 mm,

an operating voltage of 5V or more, but not more than 35V,

a heat resistance of not more than 80 °C,

an over-moulded 8 pin MiniFit male connector on one end,

either a 6 pin MiniFit socket or two over-moulded AMP connectors on the other end,

a over-moulded resistor inside the connector, and

a moulded strain relief on the cable,

whether or not with a over-moulded diode inside a connector

a length of not more than 1300 mm,

an operating voltage of 5 V or more, but not more than 35 V,

a heat resistance of not more than 80 °C,

either an over-moulded 8 pin MiniFit male connector or an over-moulded 6-pin DIN male connector on one end, and

either an over-moulded 8 pin MiniFit socket or an 8 pin MicroFit male connector on the other end

of a voltage of not more than 80 V,

with a length of not more than 120 cm,

fitted with connectors,

of a voltage of 5 V,

with a length of not more than 300 mm,

with individual conductor wires of a diameter exceeding 0,51 mm,

for a voltage of not more than 1000 V,

of a voltage of not more than 80 V,

of a platinum-iridium-alloy,

coated with poly(tetrafluoroethylene),

without connectors,

a laser diode and a photodiode operating at a typical wavelength of 635 nm or more but not more than 815 nm

an optical lens

a Recording Photodetector Integrated Circuit (PDIC)

a focussing and tracking actuator

solely consisting of one or more TFT glass or plastic cells,

combined with touch screen facilities,

with one or more printed circuits boards with control electronics for pixel addressing only,

with or without backlight unit, and

with or without inverters

with a rating of 13,5 V (± 0,5 V), and

a ball screw mechanism to control brake fluid pressure in the master cylinder,

operating within the service brake disk,

with a diameter of 170 mm or more but not more than 195 mm,

with a hydraulic torque converter,

without transfer box and cardan shaft,

whether or not with front differential,

at least eight gears,

an engine torque of 300 Nm or more, and

transverse or longitudinal installation,

one exterior-splined output shaft,

a rotary switch to indicate gear position,

the potential for a differential,

cast aluminium body,

differential gear,

2 electrical motors and gears,

a width of 300 mm or more but not more than 350 mm,

a height of 420 mm or more but not more than 500 mm,

a length of 500 mm or more but not more than 600 mm,

of a length of 1 m or more but not more than 2 m,

of a weight of 6 kg or more but not more than 9 kg

two electro-magnetic one direction clutches in one cage, working in both directions,

an input shaft with outer diameter of 24 mm (± 1 mm), ended with spline of 22,

a coaxial output bushing with inner diameter of 22 mm or more but not more than 30 mm, ended with spline of 22 teeth or more but not more than 28 teeth,

with double-row ball bearing,

whether or not with impulse (encoder) ring,

whether or not with antilock brake system (ABS) sensor,

whether or not with mounted screws,

a metal holder with three mounting screws, and

a rubber bump,

an insulating area flatness of not more than 0,1 mm,

a permissible particle quantity of 0,3 mg per tank,

a distance between pores of 2 mm or more,

pore sizes of not more than 0,4 mm, and

not more than 3 pores larger than 0,2 mm,

one solid aluminium tube whether or not with mounting bracket,

one flexible rubber hose, and

one metal clip,

designed to be bolted onto a splined shaft of outer diameter 23 mm,

with an overall diameter of not more than 266 mm (± 1 mm),

comprised of 2 sheaves with tapered faces,

sheaves having taper of 13 degrees each,

having a main compression spring used to resist displacement between sheaves, and

comprised of a cam or spring to maintain proper belt tension,

88 more provisions are not shown here; each has its own address.

Versions

1. 2018-12-20

Cited by

• Commission Implementing Regulation (EU) 2019/2092 of 28 November 2019 imposing a definitive countervailing duty on imports of biodiesel originating in Indonesia Regulation · Grade B

  The Commission noted that suspension of duties subject to end-use customs supervision has been granted on some imports of fractionated methyl esters as set out in Council Regulation (EU) 2018/2069. However, this relief concerns only the autonomous Common Customs Tariff duties and is without prejudice to the application of the countervailing duties. Consequently, the Commission rejected the end-use relief request as far as the application of the countervailing duties is concerned.